Search results for: 'bolt tabl hous stall do'
-
Flush Metal Partition Keeper Bumper Inswing
The Flush Metal Toilet Partition Keeper Bumper Inswing is for use on 1-1/4" thick square edged pilaster posts. It is constructed of Zamac die cast metal that is then chrome plated and polished. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5110. Shipped with mounting screws.
9FL925 -
Continuous U Bracket Stamped Stainless Steel 1" x 1-3/8" X 54"
Toilet Partition Continuous "U" Wall Bracket For 1" Thick Panel Stamped Stainless Steel
18 gauge (.05" thick) stamped stainless steel construction. Base is 1-1/8" x 54" long. Legs project out 1-1/2" with the thru hole at 1-1/8" from the base. Mounting and thru bolts every 13" or so. Manufacturer part # 2799.
Screws included with bracket.
9A2799 -
Stamped SS Continuous 'U' Bracket 1/2" x 1-3/8" X 57"
Stamped SS Continuous 'U' Bracket 1/2" x 1-3/8" X 57". 18 gauge (.05" thick) stamped stainless steel construction. Base is 1-1/8" x 57" long. Legs project out 1-1/2" with the thru hole at 1-1/8" from the base. Mounting and thru bolts every 13" or so. Manufacturer part # 2669. Screws included with bracket.
9A2669 -
Hadrian Headrail for 1" solid plastic
Hadrian Partitions Aluminum Headrail for 1" thick material Type A used on overhead braced floor mounted Solid Plastic Partitions. The headrail goes over the top of the pilaster which is 1" for the headrail to fit over the top of the pilaster. The slot is for 1/4" curtain hook. The headrail bolts to the pilaster for stability at the top. Overall dimension is 1-1/4"x1-3/4"ht. Also known as part number 620060, 620074.
Also known as Part# 9HR60SP, 9HR74SP and 9HR96SP.
9HRXXSP -
Global Partition Plastic Laminate Panel Dividers
Global Partition selling online all plastic laminate panel dividers. All toilet partitions ship in 48 hours, 2-4 days travel. Panels Includes 4 standard chrome brackets. Available for the following widths 16-76" and are 1" thick. Actual width is 1/2" less.
9TPLXX -
Global Partition Plastic Laminated Pilasters
Global partitions plastic laminate pilasters are for commercial use. All toilet partitions ship in 48 hours, 2-4 days travel. The pilasters Include floor mounting hardware and stainless steel shoes and are 1" thick. Available for the following widths are available in 3- 24". The pilasters are for overhead braced units that use an aluminum headrail to brace the top of the pilasters. A plastic laminate pilasters are 1" thick and 85" high. If yours are less you can cut the top off and the headrail will cover the top.
9TLLXX -
Continuous Door Stop for 1-1/4" Pilaster
Toilet partition continuous door stop for powder coated steel partitions, this has a slight round edge for attaching. The length is 57" and is used on a 1-1/4" slight round edge pilaster for mounting. Used with 1" doors and has a concealed turn latch with the pin coming out the center edge of the door. The hole spacing for the slot is 28-1/2" dead center of unit. The slot for the bolt to lock to is 7/16" wide x 5/8"ht. This helps with blocking the door gaps on the locking side of the door. This is made of brushed aluminum material and is used with in or out swing doors. Also known as Hadrian partitions part number 560058.
9A560058 -
Hadrian Stainless Steel Pilaster
Hadrian Smooth Stainless Steel Pilasters ship out in 48 hours for quick delivery's. The pilaster includes the stainless steel shoe and floor hardware. Hadrian's pilaster has a u shape at the top for a headrail to slide into and bolt to to stabilize the partitions better.
9TLSSH -
Scranton Solid Plastic Partition Between Wall
Scranton Products solid plastic between wall partitions traditionally called Hiny Hider Partitions are great for moisture and high traffic commercial buildings. All plastic material is 1" thick, doors are self closing by gravity 8" aluminum hinges or a continuous spring piano hinge, all hardware is standard aluminum brackets. Offering only Classic color collect on the website, all textures please submit drawings for us to quote with color you are looking for. All doors and panels are 55" ht, pilasters are 82" ht mounted to the floor and an overhead aluminum headrail running across the top to support the top of the pilasters. Up to 8 standard stalls total or 7 standard and 1 Ada stall. All Scranton partitions colors take 3 weeks from the time you place the order. To have an Ada stall you must select 1 Ada 24x60, plus 1 standard stall for 1 complete 60x60 ada stall. To have an Ada stall & standard stall, you must select 2 standard stalls and 1 Ada stall 24x60.
SPBWS -
Metpar Toilet Partitions Pintle For Laminate
The Metpar Toilet Partitions Pintle For Laminate restroom stalls. It is constructed of steel and white nylon plastic. The pintle is 1/2" diameter by 2-5/16" high. The threads are 5/16-18. Also known as a Bathroom Stall Pintle. Manufacture part # 98265. Shipped with lock washers and nut.
9CP350 -
Ampco Toilet Partition Pintle Laminate
The Ampco Toilet Partition Pintle Laminate is for laminate restroom stalls. It is constructed of steel and white nylon plastic. The pintle is 1/2" diameter by 2-5/16" high. The threads are 5/16-18. Also known as a Bathroom Stall Pintle. Manufacture part # 98265. Shipped with lock washers and nut.
9CP350. -
Bobrick Toilet Partition Top Hinge Pin
The Bobrick Toilet Partition Top Hinge Pin is used on there Plastic Laminate restroom stalls. The pin features knurled steel construction, and is 3-1/2" long by 3/8" diameter. The knurled end has a threaded hole of a 10-24 screw. Also known as a Bathroom Stall Hinge Pin. Manufacture part # 99109.
9FL625. -
Metpar Top Hinge Pin 3/8" x 3-1/4"
The Metpar Toilet Partitions Top Hinge Pin is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9C3504 -
Flush Metal Partition Top Hinge Pin
The Flush Metal Partition Top Hinge Pin is used on there Plastic Laminate restroom stalls. The pin features knurled steel construction, and is 3-1/2" long by 3/8" diameter. The knurled end has a threaded hole of a 10-24 screw. Also known as a Bathroom Stall Hinge Pin. Manufacture part # 99109.
9FL625 -
Metpar Toilet Partition Top Hinge Pin For Laminate
The Metpar Toilet Partition Top Hinge Pin For Laminate is used on there Plastic Laminate restroom stalls. The pin features knurled steel construction, and is 3-1/2" long by 3/8" diameter. The knurled end has a threaded hole of a 10-24 screw. Also known as a Bathroom Stall Hinge Pin. Manufacture part # 99109.
9CP450 -
Flush Metal Partition Pintle 1/2"
The Flush Metal Partition Pintle 1/2" is for laminate restroom stalls. It is constructed of steel and white nylon plastic. The pintle is 1/2" diameter by 2-5/16" high. The threads are 5/16-18. Also known as a Bathroom Stall Pintle. Manufacture part # 98265. Shipped with lock washers and nut.
9FL750 -
American Sanitary Top Hinge Pin Laminate
The American Sanitary Toilet Partition Top Hinge Pin Laminate is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9AM125 -
Generic 8 inch Top Hinge Repair Kit, Plastic Rod
Plastic Rod works with most manufactures like Global, Hadrian, Accurate Toilet Partitions. This is the replacement pin used on Solid Plastic restroom stall top hinges. These might not fit exactly. Shave off two sides to make smaller. The configuration is the same for all manufactures, some just a little wider in the diameter. Also known as a Bathroom Stall 8" Top Repair Kit. Manufacture part # 8465.
9HHGB-TOP -
Chrome Plated U Bracket 1" X 1-1/2" X 1-3/8"
Partition "U" Bracket Chrome Plated 1" X 1-1/2" X 1-3/8" . If your toilet partition or bathroom stall wall bracket is cast with the number 1910 on the back, then you have the “U” Wall Bracket for 1″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-1/4″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall “U” Bracket, or “U” Wall Bracket.
9A0191 -
General Top Hinge Pin 3/8" Dia 3-1/4" Long For Laminate
The General Top Hinge Pin 3/8" Dia 3-1/4" Long For Laminate is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
91503B -
Accurate Partition Stainless Steel Between Walls
Accurates commercial stainless steel between walls bathroom partitions floor mounted overhead braced stalls with a smooth surface. Standard stalls 36" x 60" depth (24" door), ADA stall 60" x 60" depth (36" door). Standard chrome plated alloy hardware included. Doors can be either in or out swing. Up to 8 standard stalls total or 7 standard and 1 ada stall. All toilet partitions ship in 48-72 hours plus 2-4 days travel. To have an ADA stall you must select 1 ADA 24x60, plus 1 standard stall for 1 complete 60x60 ada stall. To have an ADA stall & standard stall, you must select 2 standard stalls and 1 ADA stall 24x60. New Style slide latch with indicator in chrome plated version included. New Door style are Integrated for no gap off doors.
SSBWA -
Global Toilet Partitions Top Hinge Casting
The Global Toilet Partitions Top Hinge Casting is for use on there metal restroom stalls. It is constructed of Zamac die cast metal. The outside dimensions of the top hinge casting are 5-1/8" high by 2-5/8" deep by 25/32" wide. Two of the three holes are 3/8" diameter, and the other hole is threaded for a 5/16-18 screw. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4556.
9G0220 -
Flush Metal Partition Top Hinge Casting
The Flush Metal Partition Top Hinge Casting is for use on there metal restroom stalls. It is constructed of Zamac die cast metal. The outside dimensions of the top hinge casting are 5-1/8" high by 2-5/8" deep by 25/32" wide. Two of the three holes are 3/8" diameter, and the other hole is threaded for a 5/16-18 screw. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4556.
9FL265 -
Two Ear Bracket For 1-1/4" X 1-1/2"X 2-1/2" L
If your toilet partition (bathroom stall) wall bracket is stamped 1830, then chances are you have the Two Ear Wall Bracket for 1-1/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-15-16″ long with 3″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket, they can be ordered on our website.
9A0183 -
Partition "U" Bracket Chrome Plated For 7/8" X 1-1/2" X 1-3/8
Partition "U" Bracket Chrome Plated For 7/8" X 1-1/2" X 1-3/8 . If your toilet partition or bathroom stall wall bracket is cast with the number 1900 on the back, then you have the “U” Wall Bracket for 7/8″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-5/32″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall “U” Bracket, or “U” Wall Bracket.
9A0190 -
Global Top Pin 3/8" x 3-1/4"
The Global Toilet Partitions Top Pin is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9G2252 -
Flush Metal Top Hinge Pin
The Flush Metal Toilet Partition Top Hinge Pin is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9FL125 -
Continuous Hinge Stainless Steel,71-1/2"Lh Inswing Rh Outswing
Continuous Hinge Stainless Steel, is 71-1/2" long by 3" wide, and is for use on Right Out Swing, Left In swing restroom stall doors. The hinge is constructed of 16 gauge (.060" thick) stainless steel and the screws are placed every 11" or so. The hinge pin is 1/8" diameter, and the mounting holes are 9/32" diameter. This hinge is also known as a Full Length Toilet Partition Continuous Hinge. The Bathroom Stall hinge can be raised up 3/8" for emergency entry. See "More Views" for handing information. Manufacture part # 7769
9A7769 -
Partition Two Ear Bracket For 7/8" x 1-1/2" x 2-1/2" L
If your toilet partition (bathroom stall) wall bracket is stamped 1630, then chances are you have the Two Ear Wall Bracket for 7/8″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-1/2″ long with 2-3/4″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket.
9A0163