Door Stops

All keeper bumpers and stops are in stock for fast delivery. We carry in stock chrome plated, cast stainless steel and aluminum partition keeper bumpers. Replacing old hardware with new will change your bathroom's to looking new again. All partition keeper bumpers will come with security screws. All throw latch keepers are required for all handicap doors over 32", 34", 36" width for easy access to the inside door.

View as Grid List

Items 1-36 of 92

per page
Set Descending Direction
Page
  1. Accurate Partition Concealed Keeper Bumper 1 1/4" Round Edge

    The Accurate Partition Concealed Keeper Bumper 1 1/4" Round Edge is used on Accurate Partitions Corp. 1-1/4" thick metal round edged pilasters.  The keeper is constructed of die cast metal that is then chrome plated and then buffed to a polished finish.  The slot on the edge is designed to receive the latch bolt.  The manufactures part number is 50-8511530.

    9HACL1
    $12.65
  2. Global Toilet Partitions Keeper Bumper Concealed

    The Global Toilet Partitions Keeper Bumper Concealed is for use with concealed latches that have 1-1/4" thick squared edged pilaster posts.  They are constructed of Zamac die cast metal that is chrome plated and then polished.  Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510.  Shipped with mounting screws.

    9G150C
    $7.40
  3. Partition Keeper For Throw Latch

    The Partition Keeper For Throw Latch is for use on inswinging doors.  Keeper base is 2-1/2" high by 1-3/16" wide with a 1-1/2" hole spacing. Strike is 2-1/2" tall by 7/8" deep. The material 1/8" thick. The slot is 13/16" high by 1/4".  They are constructed of Zamac die cast metal that is then chrome plated and polished.   Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5180.  Shipped with mounting screws.

    9S2701
    $5.12
  4. Sanymetal Toilet Partition Door Stop

    The Sanymetal Toilet Partition Door Stop is constructed of Zamac die cast metal that is then chrome plated and polished.   The strike and keeper measure 2-1/2" high by 1-7/8" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5170.  Shipped with mounting screws.

    9S2704
    $5.69
  5. Bobrick Partition Keeper Bumper Inswing

    The Bobrick Partition Keeper Bumper Inswing is constructed of chrome plated Zamac die cast metal.  The keeper is designed for 1" thick squared edged pilaster posts.  Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. The slot is 5/16" deep by 1-1/2" high. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing 1". Manufacture part # 5620.  Shipped with mounting screws.

    9A5620
    $13.28
  6. Bobrick Partition Keeper Bumper Outswing

    The Bobrick Partition Keeper Bumper Outswing is designed for use on a 1" thick square edged pilaster post.  The keeper is constructed of die cast metal and then chrome plated.  Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5720.  Shipped with mounting screws.

    9A5720
    $10.12
  7. Bobrick Partitions Inswing Keeper Bumper For Throw Latch For 1" Sq Edge

    The Bobrick Partitions Inswing Keeper Bumper For Throw Latch For 1" Square Edge is constructed of chrome plated Zamac die cast metal.  It is designed for use on 1" thick square edged pilaster posts, and features a slot for a throw latch.  The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5820.  Shipped with mounting screws.

    9A5820
    $10.12
  8. Fiat Partition Keeper Bumper Inswing

    The Fiat Partition Keeper Bumper Inswing is for use on 1-1/4" thick square edged pilaster posts.  It is constructed of Zamac die cast metal that is then chrome plated and polished.  The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5110.  Shipped with mounting screws.

    9F0304
    $7.17
  9. Fiat Partition Keeper Bumper Outswing

    The Fiat Partition Keeper Bumper Outswing is designed to be mounted on 1-1/4" square edged pilaster posts.   It is constructed of Zamac die cast metal that is then chrome plated and polished.  The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for outswinging doors. Also known as a Bathroom Stall Strike and Keeper-Outswing 1-1/4". Manufacture part # 5210.  Shipped with mounting screws.

    9F0303
    $6.77
  10. Partition Inswing Keeper For Throw Ltc For 1-1/4" Sq Post

    The Partition Inswing Keeper For Throw Latch for use on a 1-1/4" Square Post or pilaster.  They are constructed of Zamac die cast metal that is then chrome plated and polished.   The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 13/16" high by 1/4" deep. Commonly known as a Bathroom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5340.  Shipped with mounting screws.

    9S410T
    $8.67
  11. Fiat Partition Keeper Bumper Concealed

    The Fiat Partition Keeper Bumper Concealed is constructed of Zamac die cast and polished chrome plate.  Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a1/2" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5960.  Shipped with screws for mounting.  Same as the 9S8861

    9F0227
    $7.08
  12. Mills Toilet Partitions Keeper Bumper Concealed

    The Mills Toilet Partitions Keeper Bumper Concealed is for use on 1-1/4" thick round edged pilaster posts.  Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. They are constructed of Zamac die cast metal that is then chrome plated and polished.  Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510.  Shipped with mounting screws.

    90T317
    $6.33
  13. Hiny Hider Inswing Flat Stop 6"

    The Hiny Hider Inswing Flat Stop 6" has Clear anodized aluminum construction. The strike and keeper is 6" tall by 2-9/16" deep and 3/4" thick on the stop. The material is 1/8" thick. The mounting holes are 3" on center. And the locking slot is 1-1/2" high by 3/8" deep. Also known as a Bathroom Stall Strike and Keeper-Inswing Flat. Manufacture part # 5798.  Shipped with mounting screws.

    9A5798
    $17.71
  14. Hiny Hider Outswing Flat Stop 6"

    The Hiny Hider Outswing Flat Stop 6" has Clear Anodized aluminum construction. The strike and keeper is 6" tall by 1-5/8" deep by 1/8" thick. The stop is 9/16" deep by 3/4" wide with a rubber insert. The mounting holes are 3" on center. Also known as a Bathroom Stall Flat Backed for Wall Mounting Strike and Keeper. Manufacture part #5898.  Shipped with mounting screws.

    9A5898
    $17.71
  15. Knickerbocker Partition Keeper Bumper 1-1/4" Round Edge

    The Knickerbocker Partition Keeper Bumper 1-1/4" Round Edge is used on 1-1/4" thick round edged pilaster posts and doors with a concealed latch.  The keeper is constructed of Zamac die cast metal that is chrome plated and polished.  This piece is used by Knickerbocker and General Partitions on there restroom stalls.  It sometimes known as part # 152ZAP or 5470.

    9K0152
    $27.83
  16. Knickerbocker SS Partition Keeper Bumper for Laminate

    The Knickerbocker Partition Keeper Bumper for Laminate restroom stalls is for use on 1-1/4" thick square edged pilaster posts.   These are usually used on Plastic Laminate or Formica stalls with a concealed latch.  They are constructed of Cast Stainless Steel. The manufacturer's part number is 152-csm.

    9K1152SS
    $56.93
  17. Hadrian Partition Keeper Bumper Cast SS

    The Hadrian Partition Keeper Bumper Cast SS is for use on 1-1/4" thick round edged pilaster posts.  The rectangular slot measures 9/16" by 11/16" and is meant to be the receiver for a concealed latch.  They are constructed of cast stainless steel and then brushed to the proper finish.  The manufactures part number is 601800-700.

    9HH810
    $17.08
  18. No Sight Partition Door Gap Filler Kit

    Global partitions No sight partition door gap filler for powder coated steel partitions or stainless steel material. The doors are typically 1" thick. The hinge side filler has a slight round edge. On the latch side there is also a slight round edge for mounting, there is a built in notch for the slide bolt that comes out the center of the doors to lock into. This kit can be used for an in swing or out swing door. The construction is aluminum and easy to shorten if needed. This product is used with 1-1/4" edge with a slight round edge to it. All security screws included for installation. The product is made by Global Partitions with part numbers 40-8443721.

    9A8443721
    $97.75
  19. Continuous Door Stop for 1-1/4" Pilaster

    Toilet partition continuous door stop for powder coated steel partitions, this has a slight round edge for attaching. The length is 57" and is used on a 1-1/4" slight round edge pilaster for mounting. Used with 1" doors and has a concealed turn latch with the pin coming out the center edge of the door. The hole spacing for the slot is 28-1/2" dead center of unit. The slot for the bolt to lock to is 7/16" wide x 5/8"ht. This helps with blocking the door gaps on the locking side of the door. This is made of brushed aluminum material and is used with in or out swing doors. Also known as Hadrian partitions part number 560058.

    9A560058
    $86.25
  20. Bobrick Inswing Keeper

    Bobrick inswing keeper for door latch. Also known as 1040-35. Used with slide latch for assembly

    1040-35
    $17.71
  21. Hiny Hider Aluminum 6" Inswing Strike And Keeper For 1" Post

    The Hiny Hider Aluminum 6" Inswing Strike And Keeper For 1" Post has Clear Anodized aluminum construction.  Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. The slot is 3/8" deep by 1-1/2" high. Also known as a Bathroom Stall Strike and Keeper Inswing 1". Used mostly on Solid Plastic (HDPE) Toilet Partitions. Some manufacture part #'s are 5778, HSISA, and 650-2873.  Shipped with mounting screws.

    9HSISA
    $15.18
  22. Mills Toilet Partitions Keeper Bumper Surface Mount

    The Mills Toilet Partitions Keeper Bumper is for use on round edged pilaster posts.  The strike and keeper measure 2-1/4" high by 29/32" wide and 15/16" deep. The hole spacing is 1-5/8" on center. They are constructed of Zamac die cast metal that is then chrome plated and polished.   Also known on Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5550.  Shipped with mounting screws.

    90T316
    $13.56
  23. Partition Keeper Bumper Inswing Flat Stop Chrome Plated

    The Partition Keeper Bumper Inswing Flat Stop Chrome Plated is a strike and keeper that measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick.  The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-19/32" on center. They are constructed of Zamac die cast metal that is then chrome plated and polished.   Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5140.  Shipped with mounting screws.

    90T116
    $5.88
  24. Hinge Sightline Filler for Partition Door Gaps

    Toilet partition door hinge side sightline filler for 1-1/4" thick powder coated steel pilaster post. This product has a slight round edge specifically for this material. The demensions are 1-1/4"x 54-1/2", this product is brushed aluminum and can be cut in the field. This product will help block the gap on the toilet partition hinge side. Known as 560458 from Hadrian partitions and can be used with other factories.

    9A560458
    $69.00
  25. Bobrick Outswing Keeper

    Bobrick outswing keeper for door latch. Also known as 1040-36. Used with slide latch for assembly

    1040-36
    $35.42
  26. Hiny Hider Aluminum 6" Outswing Keeper Bumper For 1"

    The Hiny Hider Aluminum 6" Outswing Keeper Bumper For 1" pilaster post has Clear Anodized aluminum construction. Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. Also known as a Bathroom Stall Strike and Keeper outswing 1". Used mostly on Solid Plastic (HDPE) Toilet Partitions.  Shipped with mounting screws.

    9HSOSA
    $15.18
  27. Bobrick Flat Mount Keeper

    Bobrick flat mount keeper for door latch. Also known as 1040-39. Used with slide latch for assembly

    1040-39
    $24.04
  28. Full Length Door Stop for 3/4" Material

    Full length aluminum door stop for 3/4" material used with phenolic commercial toilet partitions or posts that are 3/4" thick. This product will help any gap from the front view of the toilet stall door on the latch side. For an out swing door the slide bolt latch locks onto the opposite side of the bumper. For an in swing door the kit comes with a simple stainless steel keeper that is mounted on the inside of the stall on the post for the latch to lock to. This kit is used for an inswing or an outswing door. The spec sheet is attached, the overall height is 53-1/2". The product is made by Global Partitions with part numbers 40-8454500 and 40-8262370.

    9A8454500
    $78.20
  29. General Toilet Partitions Keeper Bumper Concealed

    The General Toilet Partitions Keeper Bumper Concealed is for used with concealed latches and 1-1/4" thick square edged pilaster posts.  It is constructed of Zamac die cast metal that is chrome plated and polished.  The keeper and strike is 2-1/2" tall by 1-7/8" wide. The stop is 17/32" thick and projects out 3/4". The mounting holes are 1-1/2" on center. The locking slot is 7/16" deep. Generally used with concealed latches. Also known as a Bathroom Stall Strike and Keeper - Inswing/Outswing 1-1/4". Manufacture part # 5230.  Shipped with mounting screws.

    92560E
    $7.84
  30. Partition Surface Keeper Inswing Cast SS 1-1/2" Screws

    Partition Inswing Surface Keeper 1-1/2" Between Screws Cast Stainless Steel

    Cast stainless steel construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5163.

    Shipped with mounting screws.

    9A5163
    $13.80
  31. Partition Keeper Bumper- Inswing For 1-1/4"

    The Partition Keeper Bumper- In swing For 1-1/4"  is for in swinging doors and pilaster posts of 1-1/4" thickness.  The bracket is constructed of die cast metal and then chrome plated and polished.  The Keeper is used by many manufactures.  The manufacture part # is 40-8512353.

    9A2353
    $11.39
  32. Partition Keeper Bumper Cast SS For 1" Sq Post

    Partition Keeper Bumper For 1" Square Post Outswing Cast Stainless Steel

    Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Outswing 1". Manufacture part # 5723.

    Shipped with mounting screws.

    9A5723
    $18.04
  33. Partition Keeper Bumper- Outswing For 1-1/4" Sq Edge

    The Partition Keeper Bumper- Outswing for 1-1/4" Sq Edge is for out swinging doors and square edged pilaster posts of 1-1/4" thickness.  The Keeper is constructed of die cast metal that is then chrome plated.  Used on many toilet partition manufacturers partitions, the manufactures part # is 40-8512354.

    9A2354
    $11.39
  34. Full Length Door Stop for 1" Material

    Full length aluminum door stop for 1" material used with solid plastic commercial toilet partitions or posts that are 1" thick. This product will help any gap from the front view of the toilet stall door on the latch side. For an out swing door the slide bolt latch locks onto the opposite side of the bumper. For an in swing door the kit comes with a simple stainless steel keeper that is mounted on the inside of the stall on the post for the latch to lock to. This kit is used for an inswing or an outswing door. The spec sheet is attached, the overall height is 53-1/2". The product is made by Global Partitions with part numbers 40-8464400 and 40-8262370.

    9A8464400
    $78.20
  35. Partition Keeper Bumper Cast SS For 1-1/4" Sq Post

    Partition Keeper Bumper For 1-1/4" Square Post Outswing Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for outswinging doors. Also known as a Bathroom Stall Strike and Keeper-Outswing 1-1/4". Manufacture part # 5213.

    Shipped with mounting screws.

    9A5213
    $17.10
View as Grid List

Items 1-36 of 92

per page
Set Descending Direction
Page