Search results for: 'restroom desk kit inswing 7 8 doan'
-
Global Top Pin 3/8" x 3-1/4"
The Global Toilet Partitions Top Pin is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9G2252 -
Partition Surface Mounted Hinge Set Lh Out, Rh Inswing
The Partition Surface Mounted Hinge Set is for use on Left Hand Out Swing and Right Hand Hand In Swinging doors. The hinges raise the door up 1/4" when opening, and then gravity causes the door to shelf close. They measure 1-1/2" center to center hole spacing on the vertical and 2-7/16" center to center on the horizontal. Constructed of cast brass with chrome plating and polished. They are also known as a Bathroom Stall Gravity Hinge Set. Manufacture part # 7011.
9A70B2 -
Toilet Partition Keeper Bumper Inswing Cast SS 1" Post Sq Edge
Partition Keeper Bumper Inswing 1" Post Square Edge Cast Stainless Steel
Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. The slot is 5/16" deep by 1-1/2" high. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing 1". Manufacture part # 5623.
Shipped with mounting screws.
9A5623 -
Flush Metal Partition Nylon Cam
The Flush Metal Partition Nylon Cam For Steel restrooms is constructed of white nylon plastic. Square part of nylon cam is 7/8" by 1-1/8" with a diameter of 11/16". The cam has an overall height of 1-1/4", with a cylinder diameter of 7/8". Also known as a Bathroom Stall Cam. Manufacture part # 98185.
9FL225 -
One Ear Bracket For 7/8" x 1-1/2" x 2-1/2"L
If your toilet partition (bathroom stall) wall bracket is stamped 1650, then chances are you have the One Ear Wall Bracket for 7/8″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 2-1/8″ long with 1-1/8″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall One Ear Bracket, Toilet Partition One Ear Bracket, Single Leg Bracket or Wall Bracket.
9A0165 -
Partition Concealed Latch Keeper Bumper Cast SS 1"
Concealed Partition Latch Keeper Bumper 1" Square Edge Cast Stainless Steel
Cast stainless steel construction. The strike and keeper measures 2-1/2" tall by 1-15/16" wide by 1-17/32 deep. The mounting holes are 1-1/2" on center. The stop measures 7/8" wide by 17/32" deep with a rubber insert bumper. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1". Manufacture part # 5733.
Shipped with mounting screws.
9A5733 -
General Toilet Partitions Keeper Bumper Concealed
The General Toilet Partitions Keeper Bumper Concealed is for used with concealed latches and 1-1/4" thick square edged pilaster posts. It is constructed of Zamac die cast metal that is chrome plated and polished. The keeper and strike is 2-1/2" tall by 1-7/8" wide. The stop is 17/32" thick and projects out 3/4". The mounting holes are 1-1/2" on center. The locking slot is 7/16" deep. Generally used with concealed latches. Also known as a Bathroom Stall Strike and Keeper - Inswing/Outswing 1-1/4". Manufacture part # 5230. Shipped with mounting screws.
92560E -
General Top Hinge Pin 3/8" Dia 3-1/4" Long For Laminate
The General Top Hinge Pin 3/8" Dia 3-1/4" Long For Laminate is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
91503B -
Partition Surface Mounted SS Hinge Set - Lh In, Rh Outswing
The Partition Surface Mounted SS Hinge Set are for use on Left Hand Inswing and Right Out Swinging Doors. One of the better reasons to use this hinge is the fact that they have a stainless steel pin in them. Nearly all of the Gravity Hinges out there use plastic pins. Stainless Steel construction, 1/8" thick. Outside dimensions of the hinge are 3-5/16" wide by 2-7/8" high. The screw spacing is 2-5/16" wide by 1-1/2" high. The mounting holes are 1/4" diameter. For use on a left hand inswing door, or right hand outswing door. See "More Views" for the handing diagram. Also known as a Bathroom Stall Gravity Hinge Set, or Toilet Partition Surface Mounted Hinge Set. Manufacture part # 7103. Shipped with mounting screws.
9A7103 -
Metpar Toilet Partition Keeper Bumper Concealed
The Metpar Toilet Partition Keeper Bumper Concealed is for use on 1-1/4" thick round edged pilaster posts and doors with a concealed latch. They are constructed of Zamac die cast metal that is then chrome plated and polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-1/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/32" deep. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5520. Shipped with mounting screws.
9OC410 -
Sanymetal Toilet Partitions Keeper Bumper Concealed
The Sanymetal Toilet Partitions Keeper Bumper Concealed is for use with concealed latches that have 1-1/4" thick squared edged pilaster posts. They are constructed of Zamac die cast metal that is chrome plated and then polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510. Shipped with mounting screws.
9S8801 -
Surface Mounted S.S. Square Barrel Hinge Set- Lh Out, Rh Inswing
The Surface Mounted. Square Barrel Hinge Set- Left Hand Out Swing and Right Hand In swing are our most heavy duty hinges. They are constructed of 1/8" thick stainless steel. 1-1/2" hole spacing up and down and 2-3/8" right to left hole spacing. Outside dimensions are 3-1/8" wide x 3" high. Also known as Bathroom Stall Gravity Hinge Sets. Manufacture part # 7052. Includes all screws.
9A7052 -
Metpar Top Hinge Pin 3/8" x 3-1/4"
The Metpar Toilet Partitions Top Hinge Pin is for plastic laminate restroom stalls. The top pin measures 3/8" diameter by 3-1/4" long with 5/16-18 threads. It has a screw driver flat slot on one end. Also known as a Bathroom Stall Door Top Hinge Pin. Manufacture part # 98584. It is constructed of threaded steel.
9C3504 -
Partition Keeper Bumper Cast SS Inswing 3/4"
Partition Keeper Bumper Inswing 3/4" Square Edge Cast Stainless Steel
Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 3/4". Manufacture part # 4903.
Shipped with mounting screws.
9A4903 -
Partition Concealed Latch Keeper Bumperr 1-1/2" Screws
Concealed Partition Latch Keeper Bumper For 1-1/2" Between Screws Cast Stainless Steel
Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5243
Shipped with mounting screws.
9A5243 -
Partition Two Ear Bracket For 7/8" x 1-1/2" x 2-1/2" L
If your toilet partition (bathroom stall) wall bracket is stamped 1630, then chances are you have the Two Ear Wall Bracket for 7/8″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-1/2″ long with 2-3/4″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket.
9A0163 -
Partition Keeper Bumper Inswing Cast SS 1" Sq Edge
Partition Keeper Bumper Inswing 1" Square Edge Cast Stainless Steel
Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5823.
Shipped with mounting screws.
9A5823 -
General Keeper Bumper For Concealed 1-1/4"
The General Keeper Bumper For Concealed 1-1/4" is for use with concealed latches that have 1-1/4" thick squared edged pilaster posts. They are constructed of Zamac die cast metal that is chrome plated and then polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510. Shipped with mounting screws.
92060B -
Sanymetal Keeper Bumper For Concealed Latches
The Sanymetal Keeper Bumper For Concealed Latches constructed of Zamac die cast metal that is then chrome plated and polished. And is designed for use on 1-1/4" thick square edged pilaster posts. Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a1/2" thick and the slot is 7/16" deep. The opening to mount it on the pilaster or post is 1-1/4" by 1-1/4". Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5960. Shipped with screws for mounting.
9S8861 -
Global Partition ADA Door Kit
The Global Partition ADA Door Kit is the manufacturer's conversion kit from regular door to ADA door. They are constructed of Zamac die cast metal that is then chrome plated and polished. The kit includes ADA handle, door stop and bumper, handles, and hinge pin. The manufactures part number is 40-8513512. If you want the complete kit, order 9G4000, which is a complete hardware package. This was used up until October 2021.
9G4000A -
Toilet Partition Keeper Bumper Chrome Plated 1-1/4" Round Edge
Chrome Plated Toilet Partition Keeper Bumper For 1-1/4" Round Edge Post
Polished chrome plated Zamac construction. The strike and keeper measure 1-1/4" high by 2-3/8" wide by 1-3/4" deep. The stop is 1/2" thick and projects out 1-1/8". The slot is 7/16" wide by 5/8" high. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5590.
Shipped with mounting screws.
9A5590 -
Partition Concealed Latch Keeper Bumper Cast SS 1-1/4"
Concealed Partition Latch Keeper Bumper 1-1/4" Square Edge Cast Stainless Steel
Cast stainless steel construction. The keeper and strike is 2-1/2" tall by 1-7/8" wide. The stop is 17/32" thick and projects out 3/4". The mounting holes are 1-1/2" on center. The locking slot is 7/16" deep. Generally used with concealed latches. Also known as a Bathroom Stall Strike and Keeper - Inswing/Outswing 1-1/4". Manufacture part # 5233.
Shipped with mounting screws.
9A5233 -
Concealed Latch Keeper Bumper Cast SS 1-1/4" Post Round Edge
Concealed Partition Latch Keeper Bumper 1-1/4" Post Round Edge Cast Stainless Steel
Cast stainless steel construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5513.
Shipped with mounting screws.
7/16" X 3/4" SLOT
9A5513 -
Accurate Partition Door Kit Stainless
The Accurate Partition Door Kit Old Style has been used from January 2013 to September 2021. The door kit is replacement hardware for an Accurate Partitions Corp. metal door. The kit includes the top and bottom hinges, nylon inserts, coat hook, keeper bumper, concealed latch and security screws. They are constructed of die cast Stainless steel. The manufactures part number is 40-8261505.
9HACL704 -
Accurate Partition ADA Door Kit Stainless
The Accurate Partition Stainless ADA Door Kit Old Style has been used from January 2013 to September 2021. The door kit is replacement hardware for an Accurate Partitions Corp. metal door. The kit includes the top and bottom hinges, nylon inserts, coat hook, keeper bumper, ADA concealed latch and security screws. This kit will convert your door to an ADA compliant door. They are constructed of cast stainless steel. The manufactures part number is 50-8261515.
9HACL705A -
Full Length Door Stop for 3/4" Material
Full length aluminum door stop for 3/4" material used with phenolic commercial toilet partitions or posts that are 3/4" thick. This product will help any gap from the front view of the toilet stall door on the latch side. For an out swing door the slide bolt latch locks onto the opposite side of the bumper. For an in swing door the kit comes with a simple stainless steel keeper that is mounted on the inside of the stall on the post for the latch to lock to. This kit is used for an inswing or an outswing door. The spec sheet is attached, the overall height is 53-1/2". The product is made by Global Partitions with part numbers 40-8454500 and 40-8262370.
9A8454500 -
Flush Metal Partition Keeper Bumper Concealed
The Flush Metal Partition Keeper Bumper Concealed is for use with concealed latches that have 1-1/4" thick squared edged pilaster posts. They are constructed of Zamac dia cast metal that is chrome plated and then polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510. Shipped with mounting screws.
9FL400 -
Bobrick Partitions Inswing Keeper Bumper For Throw Latch For 1" Sq Edge
The Bobrick Partitions Inswing Keeper Bumper For Throw Latch For 1" Square Edge is constructed of chrome plated Zamac die cast metal. It is designed for use on 1" thick square edged pilaster posts, and features a slot for a throw latch. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5820. Shipped with mounting screws.
9A5820 -
Partition Door Integral Hinge Kit
Partition Door Integral Hinge Set Top & Bottom. The bottom pin is 4-7/8" high & the top pin 3" X 1/2" high. Most manufactures used this integral hinge pin set for solid plastic partitions. The Pilasters next to the door are cut out for this door to fit in it. The hinge pins break often due to swinging on the door which causes the pin to bend and breaks the door. Manufacture part #7005.
9A7005 -
Toilet Partition Coat Hook & Bumper 3-1/2" Projection x 2-3/4" High
The Toilet Partition Coat Hook & Bumper 3-1/2" Projection x 2-3/4" High is constructed of Zamac die cast metal and then chrome plated and polished. Coat hook base is 1-1/2" wide by 2-3/4" high, with screw spacing of 7/8" at the top. Hook projects out 1". Bumper projects out 3-1/2" with a rubber insert. Also known as a Bathroom Stall Coat Hook and Bumper. Manufacture part # 4260. This product is the same as our 9OT285 and 9HA426. We find this hooks used on Global Partition Corp and Accurate Partition Corp restroom stalls.
9G0160