Search results for: 'restroom desk kit inswing 7 8 doan'
-
Toilet Partition Flat Stop Keeper Chrome Plated
Chrome Plated Toilet Partition Flat Stop Keeper
Polished chrome plated Zamac construction. The keeper base is 2-1/2" tall by 1-3/32" wide. The latch face measures 2-1/2" tall with a 7/8" projection. The hole spacing is 1-1/2". The slot measures 5/16" by 1-9/16". Also known as a Bathroom Stall Keeper-Inswing Flat. Manufacture part # 5160.
Shipped with mounting screws.
9S2401J -
Partition Bumper Keeper Chrome Plated 1" Sq Edge
Chrome Plated Toilet Partition Bumper Keeper For 1" Square Edge Post
Polished chrome plated Zamac construction. The strike and keeper measures 2-1/2" tall by 1-15/16" wide by 1-17/32 deep. The mounting holes are 1-1/2" on center. The stop measures 7/8" wide by 17/32" deep with a rubber insert bumper. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1". Manufacture part # 5730.
Shipped with mounting screws.
9A5730 -
Comtec Integral Hinge Pin Kit
Comtec Hiny Hider Partition Integral Hinge Pin Kit with heavy duty L brackets for extra strength. This kit includes everything you see in the picture. The long pin is 6" x 1/2" diameter, the smaller one is 3-1/2" x 1/2" diameter. These brackets help to reinforced the hinge pins so they do not break or the door breaking at the top and bottom.
9INTKIT -
Full Length Door Stop for 1" Material
Full length aluminum door stop for 1" material used with solid plastic commercial toilet partitions or posts that are 1" thick. This product will help any gap from the front view of the toilet stall door on the latch side. For an out swing door the slide bolt latch locks onto the opposite side of the bumper. For an in swing door the kit comes with a simple stainless steel keeper that is mounted on the inside of the stall on the post for the latch to lock to. This kit is used for an inswing or an outswing door. The spec sheet is attached, the overall height is 53-1/2". The product is made by Global Partitions with part numbers 40-8464400 and 40-8262370.
9A8464400 -
Partition Surface Mounted Hinge Set Rh Out, Lh Inswing
The Partition Surface Mounted Hinge Set is for use on Right Out Swing and Left Hand In Swinging doors. The hinges raise the door up 1/4" when opening, and then gravity causes the door to shelf close. They measure 1-1/2" center to center hole spacing on the vertical and 2-7/16" center to center on the horizontal. Constructed of cast brass with chrome plating and polished. They are also known as a Bathroom Stall Gravity Hinge Set. Manufacture part # 7021.
9A70B1 -
Partition Keeper Bumper, 1-1/4" Round Edge Outswing
The Partition Keeper Bumper, 1-1/4" Round Edge Outswing is constructed of Zamac die cast metal that is then chrome plated and polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5570. Shipped with mounting screws.
9A5570 -
Toilet Partition Concealed Latch Keeper Bumper Cast SS 1-1/4" Sq Edge
Concealed Partition Latch Keeper Bumper 1-1/4" Square Edge Cast Stainless Steel
Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a1/2" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5963.
Shipped with screws for mounting.
9A5963 -
Fiat Partition Keeper Bumper Concealed
The Fiat Partition Keeper Bumper Concealed is constructed of Zamac die cast and polished chrome plate. Keeper is 1-1/4" tall by 2-3/8" wide by 1-3/4" deep. The strike is a1/2" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5960. Shipped with screws for mounting. Same as the 9S8861
9F0227 -
Mills Toilet Partition Keeper Bumper
The Mills Toilet Partition Keeper Bumper is for use on 1-1/4" thick square edged pilaster posts. It is constructed of Zamac die cast metal that is then chrome plated and polished. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5110. Shipped with mounting screws.
90T120 -
Bobrick Angle Frame Tilt Mirror 18x30
Bobrick Angle Frame Tilt Mirror, series B-294 18x30 two position tilt mirror. This mirror is Ada approved for commercial restrooms. The outside channel is 3/4"x3/4" and is type 304 stainless steel frame. This mirror has a 7" from top wall and the bottom is mounted to wall. Standard 1/4" plate glass is used.
B294-18x30 -
Surface Mounted S.S. Square Barrel Hinge Set- Rh Out, Lh Inswing
The Surface Mounted. Square Barrel Hinge Set- Right Hand Out Swing and Left Hand In swing are our most heavy duty hinges. They are constructed of 1/8" thick stainless steel. 1-1/2" hole spacing up and down and 2-3/8" right to left hole spacing. Outside dimensions are 3-1/8" wide x 3" high. Also known as Bathroom Stall Gravity Hinge Sets. Manufacture part # 7051. Includes all screws.
9A7051 -
Global Toilet Partitions Keeper Bumper Concealed
The Global Toilet Partitions Keeper Bumper Concealed is for use with concealed latches that have 1-1/4" thick squared edged pilaster posts. They are constructed of Zamac die cast metal that is chrome plated and then polished. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5510. Shipped with mounting screws. Globals manufacturer part number 40-8511530.
9G150C -
Accurate Door Hinge Kit
Accurate and Global partitions door hinge kits for plastic laminate partitions. The top and bottom hinge kits are the exact same. The door kit includes the hinge, hinge pin, door insert, plastic cam set and all the security screws to install. This part is also known as 63160. The hinge mounts to a pilaster with 1-1/4" thickness, the doors are 1" thick.
9A63160 -
Partition Support Brace U Shape, Cut Adjustable Height
Stainless Steel Partition Support Brace U Shape, Cut Adjustable Height. Constructed of 13 Gauge Stainless Steel with Satin finish. Used to support/brace the bottom of partitions and is mounted to the restroom floor. Designed to work with partition panels or pilasters to create stability. Available for material thickness of 3/4", 7/8", 1" and 1-1/4". These partitions support braces are field adjustable by cutting the tube. Ships as standard size 12-1/2" (Max Size) and can be cut down to as small as 3"(Min Size) to create floor clearance. Features a press fit bushing to set the height for the support brace. Ships with fastners. Should you have any questions about this item please let us know. Known as part numbers 135009, 135019, 135029 and 135039.
Notes
- Only Available in U Shape Design
- Field Cut Adjustable: Ships at 12-1/2"(Max) and cuttable down to 3"(Min.)
- Thickness Available Sizes: 3/4", 7/8", 1" and 1-1/4"
9A135 -
Global Partition Stainless ADA Door Kit
The Global Partition Stainless ADA Door Kit is the manufacturer's conversion kit from regular door to ADA door. They are constructed of cast stainless steel. The kit includes ADA handle, door stop and bumper, handles, and hinge pin. The manufactures part number is 40-8263512. If you want the complete kit, order 9G500SS which is a complete hardware package. This was used up until October 2021.
9G500SSA -
Global Partition SS Door Kit
The Global Partition Complete Stainless Steel Door Kit is the manufactures hardware package. They are constructed of cast stainless steel. Included in the kit is a top and bottom hinge, concealed latch, keeper bumper, pintle, cam, coat hook and bumper, all of the hinge pins and the security screws. The manufacture part number is 40-8263501. This was used up until October 2021.
9G500SS -
European Style Indicator Latch
Occupancy Indicator Handle Set, European Design, Stainless Steel Construction. This product offers the European style with a sleek and modern feel. Features the capability of being installed on partitions with thickness of either 3/4" or 1", Built-In Handle, and Emergency unlatching access on front face of indicator, make this an extremely versatile option for restroom partitions. Traditionally these are designed for partitions that have routed edges to create a no-sightline system but can be used with non-routed edge partitions with addition hardware under related products.
901CS -
Accurate Partition Door Kit Chrome Plated
The Accurate Partition Door Kit Old Style has been used from January 2013 to September 2021. The door kit is replacement hardware for an Accurate Partitions Corp. metal door. The kit includes the top and bottom hinges, nylon inserts, coat hook, keeper bumper, concealed latch and security screws. They are constructed of die cast metal that is then chrome plated and polished. The manufactures part number is 50-8511505.
These hinges will not replace previous version of Accurates old style hinges that are no longer available.
9HACL505 -
Hadrian Headrail Return Kit Metal Stalls
Hadrian Headrail Retrun Kit is designed to work with Hadrians Metal Stall Partitions. The headrail retun kit will work with 1-1/4" thickness headrails from Hadrian. Designed to work with powder coated steel and stainless steel stalls. This kit includes Brackets,Wall Anchoring Screws, Plastic Anchors, Fastening Screws and Headrail End Cap. Can be used to run across the top of partitions either between two wall or runnning from a rear wall to a pilaster. Often used in conjuction with Hadrian Headrail (60")9HR60A, (74")9HR74A and (96")9HR96A.
Manufacturer Part# 607200.
9HH607200 -
Global Partition Standard Door Kit
The Global Partition Complete Standard Door Kit is the manufactures hardware package. They are constructed of Zamac die cast metal that is then chrome plated and polished. Included in the kit is a top and bottom hinge, concealed latch, keeper bumper, pintle, cam coat hook and bumper, all of the hinge pins and the security screws. The manufacture part number is 40-8513500. This was used up until October 2021.
9G4000 -
Accurate Partition ADA Door Kit Chrome Plated
The Accurate Partition ADA Door Kit Old Style has been used from January 2013 to September 2021. The door kit is replacement hardware for an Accurate Partitions Corp. metal door. The kit includes the top and bottom hinges, nylon inserts, coat hook, keeper bumper, ADA concealed latch and security screws. This kit will convert your door to an ADA compliant door. They are constructed of die cast metal that is then chrome plated and polished. The manufactures part number is 50-8511515.
These hinges will not replace previous version of Accurates old style hinges that are no longer available.
9HACL505A