Search results for: 'restroom doan kit itswing 7 8 dual'
-
ASI Roval Dual Sanitary Napkin & Tampon Dispenser
Roval Dual Sanitary Napkin & Tampon Dispenser Dispenses 31 napkins and 22 tampons. Door made of 18 gauge type 304 satin finish stainless steel, with two flush tumbler locks. Universal coin mechanism is convertible for 25 cents, 50 cents or FREE (no coin) operation. Coin boxes have different lock and key than doors. Wall Opening: 15 5/8" W x 25 7/8" H x 4" D
204684 -
Bathroom Door Kit Inswing 7/8" Door & 1-1/4" Post Chrome
Bathroom partition chrome plated inswing door kit for square edge doors and posts. For 7/8" doors and 1-1/4" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 17800.
9A17800 -
Bathroom Door Kit Outswing 7/8" Door & 1-1/4" Post Chrome
Bathroom partition chrome plated outswing door kit for square edge doors and posts. For 7/8" doors and 1-1/4" post. All hardware screws included for installation of these products. All hardware is a gravity close so your door self closing every time. Also known as part number 27810.
9A27810 -
Dual Desk Mount Plexiglass Brackets
Brackets designed to mount plexiglass/acrylic sheets to desk surface edge when creating separation/barrier. Brackets are adjustable for thickness from 1/8" to 3/8". It is recommended for use of 1/4" Thick material. Sold as a Pair. Made of Aluminum Alloy. Screws and inserts included. Uses a 5mm/3/16" Allen Key(Not Included) to install screws These are available in either Silver or Black Finish. Silver Finish are readily available while Black Finish may have an extended leadtime depending on quantities being ordered.
Measurements
Height: 2-1/2"
Width: 1-3/4"
Depth: 5/8"
Weight:About 1.3lb
Top to Bottom: 3-5/8"
Plate Width: 1-3/4"
Plate Length: 5-3/4"
Plate Height: 3/16"
Gap/Spacing: 1"
PRM-DDB -
Generic 8 inch Top Hinge Repair Kit, Plastic Rod
Plastic Rod works with most manufactures like Global, Hadrian, Accurate Toilet Partitions. This is the replacement pin used on Solid Plastic restroom stall top hinges. These might not fit exactly. Shave off two sides to make smaller. The configuration is the same for all manufactures, some just a little wider in the diameter. Also known as a Bathroom Stall 8" Top Repair Kit. Manufacture part # 8465.
9HHGB-TOP -
Top Hinge Assembly Chrome Plated For 7/8" Door, 1-1/4" Post
Toilet Partition Top Hinge Assembly For 7/8" Thick Door, 1-1/4" Pilaster Square Edge Chrome Plated Polished chrome plated zamac die cast construction. Kit includes Top Hinge, Pintle, Nylon Cam, and Top Hinge Door Insert. Bottom hinge measures 2-1/4" high by 1-1/4" wide with screw spacing of 1-1/2". Mounting lug projects out 1-1/4". Also known as a Bathroom Stall Bottom Hinge Kit. Manufacture part number 63020. Screws are also included.9A3020 -
Bottom Hinge Assembly Cast SS For 7/8" Door, 1-1/4" Post
The Bottom Hinge Assembly Cast SS is for use on 7/8" thick doors and 1-1/4" thick square edged pilaster posts. The hinge is constructed of cast stainless steel, that is then brushed to the proper finish. The kit includes bottom hinge, pintle, pin, insert and mounting screws. Also known as a Bathroom Stall Bottom Pivot Hinge Set. Manufacture part # 63013
9A3013 -
Chrome Plated Bottom Hinge Assembly For 7/8" Door, 1-1/4" Pilaster
The Chrome Plated Bottom Hinge Assembly For 7/8" Door, 1-1/4" Pilaster if for use on 7/8" thick doors and 1-1/4" thick squared edged pilaster posts. Hinge is constructed of Zamac die cast metal that is chrome plated and polished. Kit includes Bottom Hinge, Pintle, Nylon Cam, Bottom Hinge Door Insert and mounting Screws. Bottom hinge measures 2-1/4" high by 1-1/4" wide with screw spacing of 1-1/2". Mounting lug projects out 1-1/4". Also known as a Bathroom Stall Bottom Hinge Kit. Manufacture part number 63010.
9A3010 -
Top Hinge Assembly Cast SS For Sq Edge, 7/8" Door, 1-1/4" Pilaster
The Top Hinge Assembly Cast SS is for use on a Square Edged 1-1/4" thick Pilaster Post and 7/8" thick Door. The hinge is constructed of cast stainless steel that is then brushed to the proper finish. The kit includes top hinge, pintle, pin, inserts and mounting screws. Also known as a Bathroom Stall Top Pivot Hinge Set. Manufacture part # 63023.
9A3023 -
Keeper Inswing Stainless Steel 1-7/8" Between Screws
Toilet Partition Keeper For Inswing Doors 1-7/8" Between Screws Stainless Steel
14 gauge (.075" thick) stainless steel construction. Keeper is 2-7/8" high x 1-13/16" wide with 1-7/8" hole spacing. Lip is 9/16" and the slot or cut out is 7/32" x 1". Also known as Bathroom Stall Keeper Inswing. Manufacture part # 6319.
Shipped with screws.
9A7056 -
Global Partitions Solid Plastic 8" Wrap Door Kit
Global partitions 8" wrap door kit for Solid Plastic material. Comes in anodized aluminum finish and are for 1" thick material only. You will need to choose in or out swing when ordering. Can be used as right or left hand as hinges are field reversible. This is done by taking the 3 pieces apart and reconfiguring the opposite swing. See manufacturers numbers listed below. Used with Global and Accurate partitions.
Inswing Door Kit: 40-8441007
Outswing door Kit: 40-8441008
9G844 -
Partition Keeper Bumper Stainless Steel Inswing 1-7/8" Screws
Toilet Partition Keeper Bumper Inswing With 1-7/8" Between Screws
Stainless steel construction, 14 gauge (.075" thick). Plate measures 2-7/8" high x 1-7/8" wide including lugs. Lugs are 7/8" high and 9/16" thick. Screw holes are 1/4" diameter. Sometimes called Bathroom Stall Strike and Keeper-Inswing/Outswing Flat. Manufacuture part # 6329 and 650-8226.
Screws are included with this keeper.
9A7057 -
Partition One Ear Bracket Cast SS For 7/8" Panel
Partition One Ear Wall Bracket For 7/8" Panel Cast Stainless Steel
Cast stainless steel construction. Base of the bracket is 2" x 1-1/2", with 1-1/8" hole spacing. Bracket legs project out 2-1/2" with the screws at 2-1/8" on center from the base. The four holes are 1/4" diameter. Also known as a Bathroom Stall One Ear Wall Bracket or One Ear 7/8". Manufacture part # 1653.
Shipped with mounting screws.
9A1653 -
Toilet Partition Square Barrel Nylon Insert Replacement Hinge Kit
The Toilet Partition Square Barrel Nylon Insert Replacement Hinge Kit is for use with our 9A7051 (7413) and 9A7052 (7423) surface mounted bathroom stall hinge. The kit includes new pins for the upper and lower hinges in this 9 piece package. Replacements for 13/16"-7/8" square.
9A7405 -
Keeper Stmped Stainless Steel For 3/4" Door, 1-7/8" Between Screws
Partition Strike And Keeper For 3/4" Door, 1-7/8" Between Screws Stamped Stainless Steel
Stamped stainless steel .075" thick construction. The strike and keeper measure 2-7/8" high by 2" wide with a 1-7/8" hole spacing. The stop posts are 5/8" wide by 7/8" tall with rubber inserts. For use with 3/4" square edge posts. Also known as a Bathroom Stall Strike and Keeper Outswing 3/4". Manufacture part # 6379.
Shipped with mounting screws.
9A6379 -
Partition "U" Bracket Chrome Plated For 7/8" X 1-1/2" X 1-3/8
Partition "U" Bracket Chrome Plated For 7/8" X 1-1/2" X 1-3/8 . If your toilet partition or bathroom stall wall bracket is cast with the number 1900 on the back, then you have the “U” Wall Bracket for 7/8″ thick toilet partition panels. The wall bracket is usually mounted on the wall or the pilaster to mount the toilet partition stall panels. This bracket is 1-5/32″ wide x 1-3/8″ tall, with the through hole located at 1″ from the back. If features 4 holes with a 1/4″ diameter, with two of them on the base. The bracket is made of a die cast material that is then polished chrome plated. This bracket is sometimes called a Toilet Partition or Bathroom Stall “U” Bracket, or “U” Wall Bracket.
9A0190 -
Generic 8" Bottom Hinge Repair Kit, Plastic Rod
Generic Plastic Rod fits most manufactures like Global, Hadrian, Accurate Toilet Partitions. These might not fit exactly. Shave off two sides to make smaller. The configuration is the same for all manufactures, some just a little wider in the diameter. This is the replacement hinge pin on there Solid Plastic bottom hinges. Also known as a Bathroom Stall 8" Bottom Repair Kit. Manufacture part # 8475.
9HHGB-BOTTOM -
Continuous Stainless Steel One Ear Bracket 71", 7/8"x2-1/2"
Toilet Partition Stainless Steel Continuous One Ear Bracket, 71", 7/8"x2-1/2" 18 Gauge.
Stainless Steel Construction 18 gauge. One ear bracket is for 7/8" wide partitions and is 2-1/2" height by 2-9/32" wide by 71" long. Holes are typically spaced every 13-1/2" vertically. This bracket is also known as a Full Length Toilet Partition Continuous One Ear Bracket 71". Bracket has rounded edge radius. Designed to attach pilasters and/or panels to walls. Continuous brackets help eliminate sightline into stalls.
*Fasteners not Included *
Manufacture part # 204039
9A204039 -
Dual Access Napkin Disposal
Dual Access Napkin Disposal
Body: Type 304 #22 ga stainless steel, #4 satin finish.
Flanges: Type 304 #22 ga stainless steel, drawn one-piece construction with 1/4" returns to wall surface. One flange is welded to body the other is adjustable to fit 3/4" - 1 1/4" thick partitions. (No miters or welds)
Push Panels: Type 304 #22 ga stainless steel self closing push panel door. *International graphic symbol optional*
Waste: Type 304 #22 ga stainless steel removable from one side with pin tumbler type lock securing in place.
*Optional finger grip in lieu of lock* Also known as 0472.
9A0472 -
Hadrian Partitions Solid Plastic 8" Wrap Door Kit
Hadrain Partitions 8" wrap door kit for Solid Plastic material. Comes in anodized aluminum finish and are desgned for 1" thick material only. You will need to choose In or Out swing when ordering. Can be used as right or left hand as hinges are field reversible. To hand handing, this can be done by taking the 3 pieces apart and reconfiguring the opposite swing. See Hadrians part numbers/ known as numbers listed below. Also used with Comtec-Hiny Hiders-Scranton.
Inswing: 261005 and 261025
Outswing: 621006 and 261026
9HH621 -
Stainless Steel Slide Bolt Latch 1-7/8" Screws
Partition Surface Mounted Stainless Steel Slide Bolt Latch 1-7/8" Screws. Stamped stainless steel construction. Base is 2-7/8" high by 1-3/8" wide by 5/32" thick. Latch bolt is 2-1/4" long x 13/16" wide x 1/8" thick, and the slide distance is 25/32". Also known as a Bathroom Stall Stainless Steel Slide Latch and Toilet Partition Locks. Manufacture part # 6309. Shipped with mounting screws.
9A7055 -
Ampco Toilet Partition Bottom Door Insert For 7/8" Door
The Ampco Toilet Partition Bottom Door Insert For 7/8" Door is constructed of Zamac die cast metal and then chrome plated. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.
9CP325 -
Keeper Stainless Steel For 1" Door, 1-7/8" Between Screws
Partition Strike And Keeper For 1" Door, 1-7/8" Between Screws, Stamped Stainless Steel
Stamped stainless steel .075" thick construction. The strike and keeper measure 2-7/8" high by 2" wide with a 1-7/8" hole spacing. The stop posts are 5/8" wide by 7/8" tall with rubber inserts. For use with 1" square edge posts. Also known as a Bathroom Stall Strike and Keeper Outswing 1". Manufacture part # 6459.
Shipped with mounting screws.
9A6459 -
Metpar Toilet Partition Bottom Door Insert For 7/8" Door
The Metpar Toilet Partition Bottom Door Insert For 7/8" Door is constructed of Zamac die cast metal and then chrome plated. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.
9CP325. -
Partition Two Ear Bracket Cast SS For 7/8" Panel
Partition Two Ear Wall Bracket For 7/8" Panel Cast Stainless Steel
Cast stainless steel construction. Base is 1-1/2" x 3-1/2" with 2-3/4" hole spacing. Bracket walls are 1/8" thick. The legs project out 2-1/2" with the thru holes at 2-1/8" from the bottom of the base. Also known as a Bathroom Stall Two Ear Wall Bracket, or Two Ear 7/8". Manufacture part # 1633
Shipped with mounting screws.
9A1633 -
Toilet Partition Top Hinge Door Escutcheon For 7/8" Thick Door
The Toilet Partition Top Hinge Door Escutcheon For 7/8" Thick Doors has chrome plated Zamac die cast construction. The outside dimensions of the escutcheon are 1" deep by 1-5/8" high by 2-3/8" wide with two of the three holes with a diameter of 5/16" and one at 7/32". The inside dimensions of the U are 1" high by 2-1/16" wide. Also known as a Bathroom Stall Door Insert - Top 7/8". Manufacture part # 2740. Used on Metpar and AMPCO Toilet Partitions.
9CP425 -
Toilet Partition Keeper Stamped Stainless Steel 1-7/8" Between Screws
Partition Keeper 1-7/8" Between Screws Stamped Stainless Steel
Stamped stainless steel .075" thick construction. The keeper measures 2-5/8" high by 1-3/8" wide with a 1-7/8" hole spacing. The slot is 1-5/16" high by 5/16" high. Also known as a Bathroom Stall Keeper - Inswing. Manufacture part # 6499.
Shipped with mounting screws.
9A6499 -
Toilet Partition U Bracket Cast SS 7/8" Panel, 1-1/2" X 1-3/8" L
Toilet Partition U Bracket For 7/8" Thick Panel Cast Stainless Steel
Cast stainless steel construction. Bracket base is 1-3/8" x 1-5/32" with two mounting screw holes. Bracket legs project out 1-3/8" with the thru hole at 1" on center from the bottom of the base. Also known as a Bathroom Partition Stall U-Bracket or Wall Bracket 7/8". Manufacture part number 1903
Shipped with mounting screws
9A1903 -
One Ear Bracket Stainless Steel 7/8" Panel 1-1/2" X 2-1/2"
Toilet Partition One Ear Bracket For 7/8" Panel Stamped Stainless Steel
14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-5/16" with the mounting screws are 1-13/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1659.
Shipped with screws
9A1659 -
Knickerbocker Partition Door Latch Mechanism Kit
The Knickerbocker Partition Door Latch Mechanism Kit is used on there concealed latches. The bar measures 11/32" diameter by 3-7/16" long. The Fulcrum measures 1-11/32" by 1-11/32 by 5/16" thick. This part is also known as 8836, H749 and H748. Works with General partitions. Used with plastic laminate toilet partitions.
9K0253





































