Search results for: 'brazed tall hand stall drive'
-
Keeper Bumper For 1-1/4" Inswing Round Edge
Chrome Plated Keeper Bumper For 1-1/4" Inswing Round Edge Post
Zamac die cast and polished chrome plate construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 1-9/16" high by 5/16" deep. Commonly known as a Bathrrom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5310
Shipped with mounting screws.
9G0151 -
Pilaster Shoe Anchored for 1" Thickness
Toilet partition pilaster shoes is designed to anchor directly to floor. Shoe is constructed of 20 gauge 304 stainless steel that is stamped and welded in a satin finish with square edges. Each shoe comes with fasteners and installation torx bit. Measurement is 3" tall and is designed to hold a pilaster that is 1" wide. Partition Pilaster will sit inside the shoe. This shoe is typically used with solid plastic partitions but could be used with different types of partition materials.
9A030 -
Stainless Steel Plated Alcove Clip Set, 2 Pieces, For 1" To 1-1/4"
Toilet Partition Alcove Clip Set, 2 Pieces, For 1" To 1-1/4" Panel Stainless Steel Plated
These clips are 1-1/2" tall x 2-1/4" wide. The screws are 1-1/2" on center, with 1/4" diameter holes. The clip is constructed of cast stainless steel material. This part is also know as Bathroom Stall Alcove Clip Set, or Toilet Partition Alcove Clip. The manufacturers part number is 8343. These clips are sold in sets with the fasteners. They are used to connect a 1" panel to a 1-1/4" panel.
9A8343 -
Cast S.S. Slide Bolt Latch
Cast S.S. Slide Bolt Latch 5/8" Bar To Door, 3-1/2" Between Screws. Cast stainless steel construction. Base is 4-1/2" tall with a hole spacing of 3-1/2" on center. Latch bolt is 3-3/32" long by 1" wide by 3/16" thick and has a throw of 15/16". The latch projects out 1-9/16". The distance from the back of the base to the underside of the latch bolt is 9/16". Also known as a Bathroom Stall Slide Latch and Toilet Partition Locks. Manufacture part #5053. Shipped with screws. Used by accurate and global.
9A5053 -
Privacy Cover
The Privacy Cover is Great for Bathroom Partition Door Gaps. Block's gaps between door and pilaster for both sides. Includes 2 per package, one for each side of door, 58" Tall. The Cover is just under 2" wide with the clear rigid vinyl mounting strip being 7/8" wide, and the cover being 1-1/8" wide. This product ships in an oversize box ground. This product is not recommended for solid plastic partitions, HDPE or solid polymer material. This is great for powder coated steel, plastic laminate, stainless steel and solid phenolic materials only.
The informational and installation video are shown in the Description Tab below. In Stock for quick deliveries.
9A1010 -
Slide Bolt Latch W/Indicator Cast Stainless Steel
The Slide Bolt Latch With Indicator Cast Stainless Steel is a newer product for us. The kit includes an adjustable spindle that will work on toilet partition door thicknesses of 3/4" all the way up to 2-1/2". The latch body measures 2-11/16" by 1-5/8" tall by 1/2" thick. The hole spacing on the latch body is 1-1/8" on the vertical and 1-11/16" on the horizontal. The throw on the latch is 3/4". The indicator plate measures 1-11/16" by 2-3/8". This part is also known as the "Latch Slide S/M-Indicator-W/Keeper-Cast Stainless" and the manufacture part number is 124563.
9A1245 -
Generic 8 inch Top Hinge Repair Kit, Plastic Rod
Plastic Rod works with most manufactures like Global, Hadrian, Accurate Toilet Partitions. This is the replacement pin used on Solid Plastic restroom stall top hinges. These might not fit exactly. Shave off two sides to make smaller. The configuration is the same for all manufactures, some just a little wider in the diameter. Also known as a Bathroom Stall 8" Top Repair Kit. Manufacture part # 8465.
9HHGB-TOP -
Two Ear Bracket For 1-1/4" X 1-1/2"X 2-1/2" L
If your toilet partition (bathroom stall) wall bracket is stamped 1830, then chances are you have the Two Ear Wall Bracket for 1-1/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-15-16″ long with 3″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket, they can be ordered on our website.
9A0183 -
Partition Two Ear Bracket For 7/8" x 1-1/2" x 2-1/2" L
If your toilet partition (bathroom stall) wall bracket is stamped 1630, then chances are you have the Two Ear Wall Bracket for 7/8″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-1/2″ long with 2-3/4″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket.
9A0163 -
One Ear Bracket For 3/4" x 1-1/2" x 2-1/2"L
If your toilet partition (bathroom stall) wall bracket is stamped 1640, then chances are you have the One Ear Wall Bracket for 3/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 2″ long with 1-1/8″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall One Ear Bracket, Toilet Partition One Ear Bracket, Single Leg Bracket or Wall Bracket.
9A0164 -
One Ear Bracket For 1-1/4" X 1-1/2" x 2-1/2"
If your toilet partition (bathroom stall) wall bracket is cast 1840, then you have the One Ear Wall Bracket for 1-1/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 2-3/4″ long with 1-1/2″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall One Ear Bracket, Toilet Partition One Ear Bracket, Single Leg Bracket or Wall Bracket.
9A0184 -
Toilet Partition Square Barrel Nylon Insert Replacement Hinge Kit
The Toilet Partition Square Barrel Nylon Insert Replacement Hinge Kit is for use with our 9A7051 (7413) and 9A7052 (7423) surface mounted bathroom stall hinge. The kit includes new pins for the upper and lower hinges in this 9 piece package. Replacements for 13/16"-7/8" square.
9A7405 -
Two Ear Bracket For 3/4" x 1-1/2" x 2-1/2"L
If your toilet partition (bathroom stall) wall bracket is stamped 1620, then chances are you have the Two Ear Wall Bracket for 3/4″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3″ long with 2-7/32″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket
9A0162 -
Partition Two Ear Bracket Chrome Plated For 1" X 1-1/2"X 2-1/2"L
If your toilet partition (bathroom stall) wall bracket is stamped 1750, then chances are you have the Two Ear Wall Bracket for 1″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 3-15-16″ long with 3″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall (toilet partition) Two Ear Bracket or Wall Bracket.
9A0175 -
Pilaster Anchoring Device For 3/4" Thickness
Toilet Partition Pilaster Anchoring Device
Zinc plated steel construction. For 3/4" thick and larger Pilaster Posts and 3" wide and larger pilaster posts. The brackets are 11/16" wide. Also known as a Bathroom Stall Pilaster Post Anchoring Pack. All the screws are included in the package.
9A1056 -
One Ear Bracket Chrome Plated For 1" X 1-1/2"X 2-1/2"L
If your toilet partition (bathroom stall) wall bracket is cast 1760, then chances are you have the One Ear Wall Bracket for 1″ thick toilet partition panels. This brackets base is 1-3/8″ wide x 2-21/32″ long with 1-1/2″ center to center hole spacing. The distance from the bottom of the base to the screw holes on the legs is 2-1/8″. The bracket is made of a die cast material that is then chrome plated. The bracket sometimes goes by the name Bathroom Stall One Ear Bracket, Toilet Partition One Ear Bracket, Single Leg Bracket or Wall Bracket.
9A0176 -
Toilet Partition Chrome Plated Door Pull 3-1/2" Between Screws
Partition Door Pull 3-1/2" Between Screws Chrome Plated
Chrome plated Zamac die cast construction. The pull measures 4-3/4" wide and projects 1" with a hole spacing of 3-1/2". The mounting holes are threaded for a 10-24 screw. Also known as a Bathroom Stall Door Pull. Manufacture part # 5400.
9A0540 -
Bottom Hinge Assembly Cast SS For 7/8" Door, 1-1/4" Post
The Bottom Hinge Assembly Cast SS is for use on 7/8" thick doors and 1-1/4" thick square edged pilaster posts. The hinge is constructed of cast stainless steel, that is then brushed to the proper finish. The kit includes bottom hinge, pintle, pin, insert and mounting screws. Also known as a Bathroom Stall Bottom Pivot Hinge Set. Manufacture part # 63013
9A3013 -
Toilet Partition Door Pull Cast S.S. 2-3/4"
Partition Door Pull 2-3/4" Between Screws Cast Stainless Steel
Cast stainless steel construction. Door pull measures 4-1/16" wide by 13/16" projection with a 2-3/4" hole spacing. The holes are threaded for a 8-32 screw. Also known as a Bathroom Stall Door Pull. Manufacture part # 6203.
9A6203 -
Toilet Partition Door Stop Cast SS 2" High
Partition Door Stop 2" High Cast Stainless Steel
Cast stainless steel construction. The door stop base is 2-1/8" diameter with a 1-19/32" hole spacing. The stop projects out 2" with a rubber insert on the end of the stop. Also known as Bathroom Stall Door Stop. Manufacture part # 4123.
9A4123 -
Partition Coat Hook & Bumper Cast SS
Coat Hook & Bumper 3-1/8" Projection X 2-1/8" High Cast Stainless Steel Construction
Cast stainless steel construction. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4003.
9A4003 -
Toilet Partition Continuous 'L' Bracket Aluminum 2-3/4" X 57-1/2"
Toilet Partition Continuous 'L' Wall Bracket 2-3/4" X 57-1/2" Aluminum
Extruded aluminum construction. Base is 1-3/8" and the leg projects out 2-3/4". These are sold individually. It is also known as a Bathroom Stall Continuous L Wall Bracket. The manufacturers part # is 2684.
9A2684 -
Toilet Partition Coat Hook Cast SS 3" Projection X 1-3/4" High
Coat Hook 3" Projection x 1-3/4" High Cast Stainless Steel
Cast stainless steel construction. The hook base measures 1-3/16" wide by 1-9/16" high. The long hook projects out 3" and the short hook projects out 1-1/2". Also known as Bathroom Stall Hook. Manufacture part # 4023.
9A4023 -
Aluminum U Shape Bracket 1/2" X 1-3/8" X 57"
Aluminum U Shape Bracket 1/2" X 1-3/8" X 57". Constructed of extruded anodized aluminum. Base is 3/4 wide by 57" long, with screw holes every 13" or so. They have a clearance of 1/2" for 1/2" thick panels. Sometimes known as Bathroom Stall Continuous U Bracket. The manufacturers part numbers are 2664. These brackets are shipped with all the needed fasteners.
9A2924 -
One Ear Bracket 1" Panel, 1-1/2" X 2-1/2" L
Toilet Partition One Ear Wall Bracket For 1" Panel,Stamped Stainless Steel
14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 2-13/32" with the mounting screws are 1-15/32" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and One Wing Bracket. Manufacturer part # 1769.
Shipped with screws
9A1769 -
Partition Keeper Bumper For Throw Latch For Inswing Flat St
Chrome Plated Partition Keeper Bumper For Throw Latch, For Inswing Flat Stop
Chrome plated Zamac die casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5650.
Shipped with mounting screws.
9A5990 -
Toilet Partition Door Pull Stamped Stainless Steel 5" Between Screws
Partition Door Pull 5" Between Screws Stamped Stainless Steel
Stamped stainless steel construction, 3/32" thick. The door pull measures 5-21/32" wide by 5/8" high by 1-11/16" projection with a 5" on center hole spacing. Also known as a Bathroom Stall Door Pull. Manufacture part # 6419.
Shipped with mounting screws.
9A6419 -
Partition SS U Bracket 3/4" Panel 1-1/2" X 1-3/8" L
Partition U Bracket For 3/4" Thick Panel Cast Stainless Steel. Cast stainless steel construction. Bracket base is 1-3/8" x 1" with two mounting screw holes. Bracket legs project out 1-3/8" with the thru hole at 1" on center from the bottom of the base. Also known as a Bathroom Partition Stall U-Bracket or Wall Bracket 3/4". Manufacture part number 1893. Shipped with mounting screws.
9A1893 -
Two Ear Bracket Stainless Steel For 1" Panel, 1-1/2" X 2-1/2"
Toilet Partition Two Ear Wall Bracket For 1" Thick Panel Stamped Stainless Steel
14 gauge (.075" thick) stamped stainless steel construction. Base is 1-1/2" x 3-11/16" with the mounting screws are 2-15/16" on center. Leg project out 2-1/2" with the thru hole at 2-1/8" from the base. Also known as a Bathroom Stall Wall Bracket and Two Wing Bracket. Manufacturer part # 1759.
Shipped with screws
9A1759