Search results for: 'been thei high stall duty'
-
Hadrian Partition Top Hinge Concealed
The Hadrian Toilet Partition Top Hinge is considered a surface mounted hinge, as it mounts on the edge of the pilaster post. They are constructed of Zamac die cast metal that is then chrome plated and polished. The 9HH450 Toggle and Screw are not included with this hinge. The manufactures part numbers are 601310 and 601300.
9HH300 -
Global Partition Plastic Laminate Panel Dividers
Global Partition selling online all plastic laminate panel dividers. All toilet partitions ship in 48 hours, 2-4 days travel. Panels Includes 4 standard chrome brackets. Available for the following widths 16-76" and are 1" thick. Actual width is 1/2" less.
9TPLXX -
Knickerbocker Partition Turn Latch Knob
The Knickerbocker Partition Turn Latch Knob is the male portion of there concealed latches. The cover that goes with this latch is the 9K0255. They are constructed of Zamac die cast metal that is then chrome plated and polished. The manufacturer part number on this piece is 1410. Works with General partitions.Used with powder coated steel toilet partitions.
9K0250 -
Flush Metal Partition Latch Housing
The Flush Metal Partition Latch Housing is constructed of Zamac die cast metal. The latch body measures 3-3/8" deep by 1-15/16" high. The face plate is 3-1/4" high. The latch bolt is 11/32" diameter and has a travel of 7/16". Also known as a Flush Metal Bathroom Stall Concealed Latch Housing. Manufacture part # 6606. This part has a 1-1/4" diameter.
9A6606 -
Global Toilet Partitions Top Hinge Casting
The Global Toilet Partitions Top Hinge Casting is for use on there metal restroom stalls. It is constructed of Zamac die cast metal. The outside dimensions of the top hinge casting are 5-1/8" high by 2-5/8" deep by 25/32" wide. Two of the three holes are 3/8" diameter, and the other hole is threaded for a 5/16-18 screw. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4556.
9G0220 -
Flush Metal Partition Top Hinge Casting
The Flush Metal Partition Top Hinge Casting is for use on there metal restroom stalls. It is constructed of Zamac die cast metal. The outside dimensions of the top hinge casting are 5-1/8" high by 2-5/8" deep by 25/32" wide. Two of the three holes are 3/8" diameter, and the other hole is threaded for a 5/16-18 screw. Also known as a Bathroom Stall Door Insert - Top 1". Manufacture part # 4556.
9FL265 -
Partition Slide Bolt Latch Chrome Plated
The Partition Slide Bolt Latch Chrome Plated is constructed of Zamac die cast metal that is then chrome plated and polished. The latch measures 1-1/2" Wide X 3-1/4" High, and 2-3/4" Between Screws. We find this latch used on Accurate Partition Corp and Global Partition corp restroom stalls. Also known as a Surface Mounted Bathroom Stall Slide Latch and Toilet Partition Locks. Known as 40-8512899. Shipped with mounting screws. This latch is Ada approved.
9A2899 -
Mills Toilet Partitions Top Bottom Hinge Set
The Mills Toilet Partitions Top Bottom Hinge Set is for use on there 1-1/4" thick round edged pilaster posts. The kit includes the top and bottom hinges along with the hinge pins and the security screws. They are constructed of Zamac die cast metal that is then chrome plated and polished. The manufacture part number is HDWT-Z01.
90T100-90T110 -
Metpar Toilet Partition Bottom Door Insert For 7/8" Door
The Metpar Toilet Partition Bottom Door Insert For 7/8" Door is constructed of Zamac die cast metal and then chrome plated. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.
9CP325. -
Flush Metal Partition Bottom Door Insert
The Flush Metal Partition Bottom Door Insert is for 7/8" thick doors and is constructed of Zamac die cast metal and then chrome plated. The door insert measures 2-5/16" wide by 1" wide by 1-3/16" high. The hex shaped hole is 5/8" and the round hole is 7/32" diameter. The material or rim is 5/16" high. Also known as a Bathroom Stall Door Insert Bottom 7/8". Manufacture part # 1530.
9FL775 -
Pilaster Shoe for 1-1/4" Round Edge Thick x 3" ht
Toilet partition round edge pilaster shoe, stamped stainless steel construction. Pilaster Shoe measures 2" to 24" wide by -1-1/4" thick by 3" high. This size pilaster post shoes are split on one end for easy installation. Also known as a Bathroom Stall Pilaster Post Shoe Round Edge. Used for the base of the support system with pilaster mounting.
9A0308 -
Partition Keeper Bumper Cast SS Inswing 1-1/4" Sq Edge
Partition Keeper Inswing 1-1/4" Square Edge Cast Stainless Steel
Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 13/16" high by 1/4" deep. Commonly known as a Bathroom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5343.
Shipped with mounting screws.
9A5343 -
Toilet Partition Keeper Bumper Chrome Plated 1-1/4" Round Edge
Chrome Plated Toilet Partition Keeper Bumper For 1-1/4" Round Edge Post
Polished chrome plated Zamac construction. The strike and keeper measure 1-1/4" high by 2-3/8" wide by 1-3/4" deep. The stop is 1/2" thick and projects out 1-1/8". The slot is 7/16" wide by 5/8" high. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5590.
Shipped with mounting screws.
9A5590 -
Flush Metal Partition Coat Hook Bumper
The Flush Metal Partition Coat Hook Bumper is constructed of Zamac die cast metal that is then chrome plated and polished. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.
9FL450 -
Hiny Hider Aluminum 6" Outswing Keeper Bumper For 1"
The Hiny Hider Aluminum 6" Outswing Keeper Bumper For 1" pilaster post has Clear Anodized aluminum construction. Strike and Keeper is 6" high by 1-15/16" wide. The three mounting screws are 2" on center apart. Also known as a Bathroom Stall Strike and Keeper outswing 1". Used mostly on Solid Plastic (HDPE) Toilet Partitions. Shipped with mounting screws.
9HSOSA -
Door Hook & Bumper Stop Stainless Steel Inswing
Partition Door Hook & Bumper Stop Inswing Stamped Stainless Steel
Stamped stainless steel 1/16" thick construction. The hook and stop measures 5/8" wide by 2-3/4" high by 3-1/16" projection with a 1" hole spacing. There is a rubber bumper on the end of the 3-1/16" projection. Also known as a Bathroom Stall Hook. Manufacture part # 4009
9A4009 -
Partition Support L Brace Stainless Steel
Stainless Steel L shape Partition Brace. Do your Toilet partition panels keep falling out of the bathroom stall wall mounted brackets? If so, the answer might be a Toilet Partition brace or support, which would support the panel and pilaster from falling, or as preventive maintenance to strengthen the compartment. They are also sometimes called Pilaster Support L-Brackets. The we stock 3 versions that are adjustable from 7-1/2″ to 10″, 9-1/2″ to 12″ and 11-1/2″ to 14″, floor to bottom of panel clearance. The bathroom stall brace is made of stainless steel, with a round base of 2-3/8″ and a support bracket that is 1-1/2″ x 2-3/8″. The diameter of the toilet partition support shaft is 1″. If you have any questions on the Toilet Partition Support Braces let us know!
Same as 8513, 85183, 85193, 9a6005, 9a85183, 9a85193. Most common 9a6005.Note the most common are 11-1/2" to 14" due to the partitions are mounted 12" off the floor.
Also note quantities of 10 or more not returnable.
BRACES -
Global Ada Latch Cover & Knob Stainless Steel
The Global Partitions stainless steel Ada latch knob & cover, with Screw, are a concealed latch that is held together by a screw. They are constructed of cast stainless steel metal that is then brushed and polished. The 9G3370 meets ADA compliance codes. The manufacturer part number is 40-8263370. This was used up until October 2021.
9G3370 -
Partition Keeper Bumper For Throw Latch For Inswing Flat St
Chrome Plated Partition Keeper Bumper For Throw Latch, For Inswing Flat Stop
Chrome plated Zamac die casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5650.
Shipped with mounting screws.
9A5990 -
Toiler Partition Headrail Bracket for 1" Headrail
Partition Headrail Bracket for 1" Headrail
Chrome plate Zamac die cast construction. The overall measurements of the bracket are 2-3/4" wide by 1-19/32" high by 1" deep with a hole spacing of 2". The spread for the headrail is 1-1/8" by 1-19/32" deep. Also known as a Bathroom Stall Headrail Bracket. Manufacture part # 2150.
Shipped with screws.
9A0215 -
Koala Horizontal Mounted Baby Station KB300
The KB300 series surface mounted horizontal baby changing station is constructed of polypropylene and features a unibody steel chassis for superior strength. Available in three stunning colors with each providing a modern visual aesthetic. Thoughtful patron amenities enhance the end-user experience, and include Microban product protection, a redesigned liner dispenser and the Koala brand mark that communicates comfort to families and the promise of a thoughtful accommodation.
The dual liner cavity has an internal spring tab that pushes liners forward while only allowing single liner dispensing. Each cavity holds 25 liners and locking mechanism minimizes operator refills and discourages potential vandalism. The product includes child protection straps. Bed surface exclusively contains Microban® antimicrobial product protection that reduces odor-causing bacteria and keeps the bed surface cleaner between cleanings. Concealed pneumatic cylinder provides controlled, slow opening and closing of the changing station bed.
KB300 -
Dual Access Napkin Disposal
Dual Access Napkin Disposal
Body: Type 304 #22 ga stainless steel, #4 satin finish.
Flanges: Type 304 #22 ga stainless steel, drawn one-piece construction with 1/4" returns to wall surface. One flange is welded to body the other is adjustable to fit 3/4" - 1 1/4" thick partitions. (No miters or welds)
Push Panels: Type 304 #22 ga stainless steel self closing push panel door. *International graphic symbol optional*
Waste: Type 304 #22 ga stainless steel removable from one side with pin tumbler type lock securing in place.
*Optional finger grip in lieu of lock* Also known as 0472.
9A0472 -
Keeper Bumper For 1-1/4" Inswing Round Edge
Chrome Plated Keeper Bumper For 1-1/4" Inswing Round Edge Post
Zamac die cast and polished chrome plate construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 1-9/16" high by 5/16" deep. Commonly known as a Bathrrom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5310
Shipped with mounting screws.
9G0151 -
Keeper Inswing Stainless Steel 1-7/8" Between Screws
Toilet Partition Keeper For Inswing Doors 1-7/8" Between Screws Stainless Steel
14 gauge (.075" thick) stainless steel construction. Keeper is 2-7/8" high x 1-13/16" wide with 1-7/8" hole spacing. Lip is 9/16" and the slot or cut out is 7/32" x 1". Also known as Bathroom Stall Keeper Inswing. Manufacture part # 6319.
Shipped with screws.
9A7056 -
Toilet Partition Top Hinge Door Escutcheon For 7/8" Thick Door
The Toilet Partition Top Hinge Door Escutcheon For 7/8" Thick Doors has chrome plated Zamac die cast construction. The outside dimensions of the escutcheon are 1" deep by 1-5/8" high by 2-3/8" wide with two of the three holes with a diameter of 5/16" and one at 7/32". The inside dimensions of the U are 1" high by 2-1/16" wide. Also known as a Bathroom Stall Door Insert - Top 7/8". Manufacture part # 2740. Used on Metpar and AMPCO Toilet Partitions.
9CP425 -
Partition Concealed Latch Keeper Bumperr 1-1/2" Screws
Concealed Partition Latch Keeper Bumper For 1-1/2" Between Screws Cast Stainless Steel
Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5243
Shipped with mounting screws.
9A5243 -
Toilet Partition Headrail 1-1/4"X95" Type B
Partition Anti-Grip Headrail 1-1/4" X 95" Type B Aluminum. Extruded anodized aluminum construction. The cross section measures 2-3/4" high by 1-11/32" by 95" long. The part that fits on top of the pilaster is 1-1/4" wide by 3/4" deep. The wall thickness on this part is 3/64". Also known as a Bathroom Stall Headrail. Manufacture part # 80052.
9HR98B2 -
Ampco Toilet Partition Coat Hook Bumper
The Ampco Toilet Partition Coat Hook Bumper is constructed of Zamac die cast metal and then chrome plated. Coat hook bumper projects out 3" and has a rubber insert. The hook projects out 1-7/32". The coat hook bumper base is 1-7/16" wide by 2-1/4" high with a hole spacing of 7/8". Also known as a Bathroom Stall Hook. Manufacture part # 4000.
96200B -
Napkin / Tampon Disposal Recessed in Wall
Napkin / Tampon Disposal Recessed in Wall
Body: Type 304 #22 ga stainless steel, #4 satin finish.
Flange: Type 304 #22 ga stainless steel #4 satin finish, drawn one piece construction with 1/4" returns to wall surface. (Without miters or welds)
Push Panel: Type 304 #22 ga stainless steel self closing push panel door. *International Graphic Symbols are optional.
Waste: Type 304 #22 ga stainless steel, removable type waste, secured by pin tumbler lock. Pin tumbler commercial quality locks, keyed like all other A & J cabinets. *(Optional finger grip in lieu of lock)
9A0473 -
Toilet Partition Headrail 1-1/4"X65" Type B
Partition Anti-Grip Headrail 1-1/4" X 65" Type B Aluminum
Extruded anodized aluminum construction. The cross section measures 2-3/4" high by 1-11/32" by 65" long. The part that fits on top of the pilaster is 1-1/4" wide by 3/4" deep. The wall thickness on this part is 3/64". Also known as a Bathroom Stall Headrail. Manufacture part # 80052.
Also know as Part# 9THS621-1/4, 9THSSXX, and 9THLXX.
9HR62B2 -
Keeper Bumper For 1-1/4" Outswing Round Edge
Chrome Plated Keeper Bumper For 1-1/4" Outswing Round Edge Post
Zamac die cast and polished chrome plate construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. Commonly known as a Bathrrom Stall Strike and Keeper Outswing 1-1/4". Manufacture part # 5410
Shipped with mounting screws.
9G015E -
Metpar Toilet Partitions Bottom Cam Housing Unplated
The Metpar Toilet Partitions Bottom Cam Housing Unplated is constructed of Zamac die cast metal. The housings outside dimensions are 3-1/8" wide by 1-5/32" deep by 1-7/16" high. The screw hole is 7/32" diameter. The square slot is 1" by 15/16". The square bulge were the screw is located is 1-1/2" by 1-5/32". Also known as a Bathroom Stall Door Insert - Bottom 1". Manufacture part # 4066.
9C0140 -
Ampco Toilet Partitions Bottom Cam Housing Unplated
The Ampco Toilet Partitions Bottom Cam Housing Unplated is constructed of Zamac die cast metal. The housings outside dimensions are 3-1/8" wide by 1-5/32" deep by 1-7/16" high. The screw hole is 7/32" diameter. The square slot is 1" by 15/16". The square bulge were the screw is located is 1-1/2" by 1-5/32". Also known as a Bathroom Stall Door Insert - Bottom 1". Manufacture part # 4066.
9C0140. -
Scranton Solid Plastic Partition Between Wall
Scranton Products solid plastic between wall partitions traditionally called Hiny Hider Partitions are great for moisture and high traffic commercial buildings. All plastic material is 1" thick, doors are self closing by gravity 8" aluminum hinges or a continuous spring piano hinge, all hardware is standard aluminum brackets. Offering only Classic color collect on the website, all textures please submit drawings for us to quote with color you are looking for. All doors and panels are 55" ht, pilasters are 82" ht mounted to the floor and an overhead aluminum headrail running across the top to support the top of the pilasters. Up to 8 standard stalls total or 7 standard and 1 Ada stall. All Scranton partitions colors take 3 weeks from the time you place the order. To have an Ada stall you must select 1 Ada 24x60, plus 1 standard stall for 1 complete 60x60 ada stall. To have an Ada stall & standard stall, you must select 2 standard stalls and 1 Ada stall 24x60.
SPBWS