Door Stops

All keeper bumpers and stops are in stock for fast delivery. We carry in stock chrome plated, cast stainless steel and aluminum partition keeper bumpers. Replacing old hardware with new will change your bathroom's to looking new again. All partition keeper bumpers will come with security screws. All throw latch keepers are required for all handicap doors over 32", 34", 36" width for easy access to the inside door.

View as Grid List

Items 37-72 of 91

per page
Set Descending Direction
Page
  1. Partition Keeper Bumper Flat Stop Chrome Plated 1-1/2" Screws

    Chrome Plated Toilet Partition Keeper Bumper Flat Stop 1-1/2" Between Screws

    Polished chrome plated Zamac construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5240

    Shipped with mounting screws.

    9A5240
    $6.96
  2. Full Length Door Stop for 1" panel Inswing

    Toilet partition full length aluminum door stop for 1" panel Inswing doors. This product is clear anodized aluminum. This full length door stop with block the gap between the door and the post next to it. For an inswing the slot is 3/8"x1-1/4" wide for the slide latch to latch it. The door keeper and strike is 54" in length and has 5 holes spaced at 13" apart and starts at 1" from the top and the bottom. Also known as 134304 strike & keeper channel. Includes all hardware.

    9A134304
    $107.53
  3. Partition Keeper Bumper Flat Stop Chrome Plated 1-1/2" Screws, Outswing

    Chrome Plated Toilet Partition Keeper Bumper Flat Stop 1-1/2" Between Screws, For Outswing

    Polished chrome plated Zamac construction. The strike and keeper measure 2-1/2" high by 1-5/8" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5260

    Shipped with mounting screws.

    9A5260
    $5.12
  4. Toilet Partition Keeper Bumper Inswing Cast SS 1" Post Sq Edge

    Partition Keeper Bumper Inswing 1" Post Square Edge Cast Stainless Steel

    Cast stainless steel construction. Strike and Keeper measures 2-1/2" high by 1-15/16" wide. Stop is 17/32" thick and projects out 13/16". The screw holes are 1-1/2" on center. The slot is 5/16" deep by 1-1/2" high. This Bathroom Toilet Door Keeper is designed for use on 1" thick square edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing 1". Manufacture part # 5623.

    Shipped with mounting screws.

    9A5623
    $24.00
  5. Full Length Aluminum Door Stop for 1" panel outswing

    Toilet partition full length aluminum door stop for 1" panel outswing doors. This product is clear anodized aluminum. This full length door stop with block the gap between the door and the post next to it. For an outswing the latch locks on the back side of the bumper. The door keeper and strike is 54" in length and has 5 holes spaced at 13" apart and starts at 1" from the top and the bottom. Also known as 134314 strike & keeper channel. Includes all hardware.

    9A134314
    $107.53
  6. Partition Keeper Bumper Chrome Plated Inswing 1-1/4"

    Chrome Plated Toilet Partition Keeper Bumper Inswing 1-1/4" Round Edge

    Polished chrome plated Zamac die casting. The strike and keeper measures 1-7/8" wide by 2-1/2" tall by 1-1/2" deep. The stop measures 2-1/2" tall and projects out 3/4" and has a rubber insert. The two slots have a 1/4" opening by 13/16". Also known as a Bathroom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5330

    9A5330
    $7.79
  7. Partition Keeper Bumper Inswing Cast SS 1" Sq Edge

    Partition Keeper Bumper Inswing 1" Square Edge Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 1". Manufacture part # 5823.

    Shipped with mounting screws.

    9A5823
    $20.00
  8. Partition Keeper Bumper Cast SS Inswing 1-1/2" Screws

    Partition Keeper Bumper Inswing 1-1/2" Between Screws Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-19/32" on center. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5143.

    Shipped with mounting screws.

    9A5143
    $16.45
  9. Toilet Partitions Bumper Keeper Chrome Plated 1-1/4" Round Edge

    Chrome Plated Toilet Partitions Bumper Keeper For 1-1/4" Round Edge

    Polished chrome plated Zamac construction. The strike and keeper measures 2-1/2" tall by 1-7/8" wide. The mounting holes are 1-1/2" on center. The stop measures 3/4" wide by 17/32" deep with a rubber insert bumper. Slot is 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5430.

    Shipped with mounting screws.

    9A5430
    $13.92
  10. Partition Keeper Bumper Cast SS Inswing 1-1/4" Post Sq Edge

    Partition Keeper Bumper Inswing 1-1/4" Post Square Edge Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-7/8" wide. The stop sticks out 3/4" and has a rubber bumper on it. The two mounting screws are 1-1/2" on center. The latch bolt slot is 1-9/16" high by 5/16" deep. This keeper bumper is designed for use on a 1-1/4" Post or Pilaster for inswinging doors. Also known as a Bathroom Stall Strike and Keeper-Inswing 1-1/4". Manufacture part # 5113.

    Shipped with mounting screws.

    9A5113
    $18.98
  11. Partition Keeper Bumper, 1-1/4" Round Edge Outswing

    The Partition Keeper Bumper, 1-1/4" Round Edge Outswing is constructed of Zamac die cast metal that is then chrome plated and polished.  Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5570.  Shipped with mounting screws.

    9A5570
    $7.59
  12. Partition Keeper Bumper Cast SS Inswing 1-1/4" Sq Edge

    Partition Keeper Inswing 1-1/4" Square Edge Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-7/8" wide with a hole spacing of 1-1/2" on center. The stop is 2-1/2" tall by 3/4" wide with a rubber insert. The slot measures 13/16" high by 1/4" deep. Commonly known as a Bathroom Stall Strike and Keeper Inswing 1-1/4". Manufacture part # 5343.

    Shipped with mounting screws.

    9A5343
    $20.30
  13. Partition Keeper Bumper 1-1/4" Round Edge

    The Partition Keeper Bumper 1-1/4" Round Edge is constructed of Zamac die cast metal that is then chrome plated and polished.  Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 1/4" deep. The opening to mount it on the round edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5580.  Shipped with screws for mounting.

    9A5580
    $7.91
  14. Partition Keeper Bumper Cast SS Inswing 3/4"

    Partition Keeper Bumper Inswing 3/4" Square Edge Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper is 2-1/2" tall by 1-15/16" wide. The mounting holes are 1-1/2" on center. The stop is 2-1/2" tall by 13/16" projection with a rubber insert. The two slots are 5/16" deep by 13/16" high. Also known as Bathroom Stall Strike and Keeper Inswing 3/4". Manufacture part # 4903.

    Shipped with mounting screws.

    9A4903
    $22.00
  15. Toilet Partition Keeper Bumper Chrome Plated 1-1/4" Round Edge

    Chrome Plated Toilet Partition Keeper Bumper For 1-1/4" Round Edge Post

    Polished chrome plated Zamac construction. The strike and keeper measure 1-1/4" high by 2-3/8" wide by 1-3/4" deep. The stop is 1/2" thick and projects out 1-1/8". The slot is 7/16" wide by 5/8" high. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1-1/4". Manufacture part # 5590.

    Shipped with mounting screws.

    9A5590
    $6.33
  16. Partition Keeper Bumper Outswing Cast SS 1-1/2" Screws

    Partition Keeper Bumper Outswing 1-1/2" Between Screws Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-5/8" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5263.

    Shipped with mounting screws.

    9A5263
    $15.18
  17. Partition Keeper Flat Stop Cast SS 1-1/2" Screws

    Partition Keeper Flat Stop 1-1/2" Between Screws Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-1/2" on center. Slots are 1/4" deep by 13/16" high. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5283.

    Shipped with mounting screws.

    9A5283
    $16.45
  18. Partition Keeper Bumper Flat Stop Outswing

    Chrome Plated Partition Keeper Bumper Flat Stop Outswing Door

    Chrome plated Zamac die casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5640.

    Shipped with mounting screws.

    9A5640
    $13.20
  19. Partition Surface Door Stop Cast SS 1-1/2" Screws

    Cast Stainless Steel Partition Door Stop

    Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-7/8" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5173.

    Shipped with mounting screws.

    9A5173
    $13.50
  20. Partition Cast Stainless Steel Inswing Keeper

    Cast Stainless Steel Partition Keeper 1-1/2" Between Screws

    Cast stainless steel construction. Keeper base is 2-1/2" high by 1-3/16" wide with a 1-1/2" hole spacing. Strike is 2-1/2" tall by 7/8" deep. The material 1/8" thick. The slot is 13/16" high by 1/4". Also known as a Bathroom Stall Keeper Inswing Flat. Manufacture part # 5183.

    Shipped with mounting screws.

    9A5183
    $15.18
  21. Partition Bumper Keeper Chrome Plated 1" Sq Edge

    Chrome Plated Toilet Partition Bumper Keeper For 1" Square Edge Post

    Polished chrome plated Zamac construction. The strike and keeper measures 2-1/2" tall by 1-15/16" wide by 1-17/32 deep. The mounting holes are 1-1/2" on center. The stop measures 7/8" wide by 17/32" deep with a rubber insert bumper. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1". Manufacture part # 5730.

    Shipped with mounting screws.

    9A5730
    $14.67
  22. Partition Concealed Latch Keeper Bumper Cast SS 1"

    Concealed Partition Latch Keeper Bumper 1" Square Edge Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measures 2-1/2" tall by 1-15/16" wide by 1-17/32 deep. The mounting holes are 1-1/2" on center. The stop measures 7/8" wide by 17/32" deep with a rubber insert bumper. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing 1". Manufacture part # 5733.

    Shipped with mounting screws.

    9A5733
    $27.83
  23. Concealed Latch Keeper Bumper Cast SS 1-1/4" Post Round Edge

    Concealed Partition Latch Keeper Bumper 1-1/4" Post Round Edge Cast Stainless Steel

    Cast stainless steel construction. Strike and Keeper measures 1-1/4" high by 2-3/8" wide by 1-3/4" deep. Stop is 1/2" thick and projects out 1-1/8". The latching slot is 7/16" deep x 3/4" high. This Bathroom Toilet Door Keeper is designed for use on 1-1/4" thick round edge posts or pilasters. Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5513.

    Shipped with mounting screws.

    7/16" X 3/4" SLOT

    9A5513
    $17.00
  24. Partition Outswing Keeper Bumper 1-1/4" Post Sq Edge

    The Partition Outswing Keeper Bumper 1-1/4" Post Sq Edge is constructed of Zamac die cast metal that is then chrome plated and polished.  Keeper is 1-1/4" tall by 2-3/8" wide by 1-13/16" deep. The strike is 1/2" thick with rubber insert. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5970.  Shipped with screws for mounting.

    9A5970
    $7.59
  25. Partition Concealed Latch Keeper Bumper Cast SS 1-1/4"

    Concealed Partition Latch Keeper Bumper 1-1/4" Square Edge Cast Stainless Steel

    Cast stainless steel construction. The keeper and strike is 2-1/2" tall by 1-7/8" wide. The stop is 17/32" thick and projects out 3/4". The mounting holes are 1-1/2" on center. The locking slot is 7/16" deep. Generally used with concealed latches. Also known as a Bathroom Stall Strike and Keeper - Inswing/Outswing 1-1/4". Manufacture part # 5233.

    Shipped with mounting screws.

    9A5233
    $29.10
  26. Partition Keeper Bumper Inswing 1-1/4"

    The Partition Keeper Bumper Inswing 1-1/4" is constructed of Zamac die cast metal that is then chrome plated and polished.  Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5980.  Shipped with screws for mounting.

    9A5980
    $7.59
  27. Partition Keeper Bumper For Throw Latch Inswing Flat Stop

    Chrome Plated Partition Keeper Bumper For Throw Latch Inswing Flat Stop

    Chrome plated Zamac die casting. The strike and keeper measure 2-1/2" tall by 2-9/16" deep and is 1/8" thick. The stop projects out 3/4" and has a rubber insert. The mounting holes are 1-1/2" on center. Slots are 1/4" deep by 13/16" high. Also known as a Bathroom Stall Strike and Keeper - Inswing Flat. Flat backed for wall mounting. Manufacture part # 5280

    Shipped with mounting screws.

    9A5985
    $10.12
  28. Partition Concealed Latch Keeper Bumperr 1-1/2" Screws

    Concealed Partition Latch Keeper Bumper For 1-1/2" Between Screws Cast Stainless Steel

    Cast stainless steel construction. The strike and keeper measure 2-1/2" high by 1-13/16" deep by 1/8" thick. The stop has a 3/4" projection and is 9/16' deep with a rubber insert. The mounting holes are 1-1/2" on center. The slot is for the concealed latch is 7/8" high by 7/16" deep. Also known as a Bathroom Stall Strike and Keeper Inswing/Outswing Flat. Manufacture part # 5243

    Shipped with mounting screws.

    9A5243
    $15.18
  29. Partition Concealed Keeper Bumper Inswing Cast SS

    Concealed Partition Latch Keeper Bumper Inswing Cast Stainless Steel

    Stainless steel casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5653.

    Shipped with mounting screws.

    9A5653
    $41.75
  30. Partition Keeper Bumper For Throw Latch For Inswing Flat St

    Chrome Plated Partition Keeper Bumper For Throw Latch, For Inswing Flat Stop

    Chrome plated Zamac die casting. The strike and keeper is 1-1/4" high by 2-1/2" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. The slots are 1/4" deep. Also known as a Bathroom Stall Strike and Keeper Inswing Flat. Manufacture part # 5650.

    Shipped with mounting screws.

    9A5990
    $12.02
  31. All American Toilet Partition Keeper Bumper

    The All American Toilet Partition Keeper Bumper is for 1-1/4" thick round edged pilaster posts.  The slot measures 1/2" x 3/4".  The manufactures part number is 105.

    9AA105
    $20.00
  32. Concealed Latch Keeper Bumper Inswing Cast SS 1-1/4" Round Edge

    Concealed Partition Latch Keeper Bumper Inswing 1-1/4" Round Edge Cast Stainless Steel

    Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 1/4" deep. The opening to mount it on the round edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5583.

    Shipped with screws for mounting.

    9A5583
    $19.60
  33. Cast SS Concealed Latch Keeper Bumper Inswing 1-1/4" Sq Edge

    Concealed Latch Keeper Bumper Inswing For 1-1/4" Square Edge Post Cast Stainless Steel

    Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 2-9/16" deep. The strike is a17/32" thick and the slot is 7/16" deep. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing 1-1/4". Manufacture part # 5983

    Shipped with screws for mounting.

    9A5983
    $16.45
  34. Toilet Partition Concealed Latch Keeper Bumper Outswing Cast SS

    Concealed Latch Keeper Bumper Outswing Cast Stainless Steel

    Cast Stainless Steel casting. The strike and keeper is 1-1/4" high by 1-3/4" deep by 1/8" thick. The stop is 1/2" deep by 1-1/4 wide with a rubber insert. Also known as a Bathroom Stall Strike and Keeper Outswing Flat. Manufacture part # 5643.

    Shipped with mounting screws.

    9A5643
    $27.83
  35. Concealed Latch Keeper Bumper Cast SS Outswing 1-1/4" Round Edge

    Concealed Partition Latch Keeper Bumper Outswing 1-1/4" Round Edge Cast Stainless Steel

    Cast stainless Steel Construction. The outside dimensions are 2-3/8" wide by 1-1/4" high by 1-3/4" deep. Stop projects out 1-1/8" by 1/2" thick with a rubber insert. Designed for an 1-1/4" thick post round edge. Also known as a Bathroom Stall Strike and Keeper Outswing 1-1/4". Manufacture part # 5573.

    Shipped with mounting screws.

    9A5573
    $18.00
  36. Cast SS Concealed Latch Keeper Bumper Outswing 1-1/4" Sq Edge

    Concealed Partition Latch Keeper Bumper Outswing 1-1/4" Square Edge Cast Stainless Steel

    Cast stainless steel construction. Keeper is 1-1/4" tall by 2-3/8" wide by 1-13/16" deep. The strike is 1/2" thick with rubber insert. The opening to mount it on the square edge pilaster or post is 1-1/4" by 1-1/4" Also known as a Bathroom Stall Strike and Keeper for Inswing/Outswing 1-1/4". Manufacture part # 5973.

    Shipped with screws for mounting.

    9A5973
    $16.45
View as Grid List

Items 37-72 of 91

per page
Set Descending Direction
Page